BSE 76  
View related threads: (in this forum | in all forums)

Tower Hobbies
Enter up to 4 keywords or Tower stock numbers
Logged in as Guest



Users viewing this topic: none
  Printable Version
       


Touchstart Remote Controlled Autostart Engine .61 ASP COLLECTORS !!!!!!!!!!!!!!
Seller:  vidal_felipe
Details:   $499.00   |  7/14/2008   |  Classified Ad
We will rotate YOUR AD in this spot if you select "Forum Featured" when placing or editing your ad!

All Forums >> Glow Engines, Gas Engines, Fuel & Mfg Support Forums >> Engine Manufacturers Direct Support Forum >> Jett Engineering Support >> BSE 76
Page: [1]

Login
Message << Older Topic   Newer Topic >>
BSE 76 - 3/13/2007 7:26:53 PM   
RANIERY


 

Posts: 132
Joined: 6/9/2003
From: davie, FL, USA
Status: offline 		HI, I want to buy buy a new motor but i see it comes with three differents mufflers i know i won't need the in cowl one cause is for a OMP BOXXER profile. so what it is the difference beteween the other two mufflers and wich one it's better. we don't have problems with noise we race (q-40 here) and i want to get good transictions. any help thanks.
       Post #: 1

RE: BSE 76 - 3/13/2007 8:17:06 PM   
bob27s



Posts: 4637
Joined: 4/9/2002
From: Cleveland, OH, USA
Status: offline 		Thanks for writing....

Id suggest going with the lite-jett. We sell that as standard equipment on the 76L engines and include it with the 60L (hover) engines too. At the lower rpms these engines run at, its not that loud. Best of all it weighs next to nothing. And since it is non-tuned, there is no tendency for a pipe-step - throttle remains linear.

The other two mufflers are tuned devices. For sport, pattern or scale use, these are great when combined with the BSE-76L. I use the turbo-jett on the 76L in my Edge 540T - gives an additional 1000 rpm on the top end with a 14x4 or 14x6, really helps it swing up to a 15x6 if I ask it to, and the midrange is great - lots of torque. But for a profile application, its not the right choice - just not going to fit.

The boxxxer should be awesome with the 76L on it !!

Suggestion..... airframe mount the needle valve. In fact, you can mount it on the tank side of the fuselage if you wish. If you pass the supply line from the needle through the fuselage side right to the carb, it might make the plumbing look nicer when you are done



< Message edited by bob27s -- 3/13/2007 8:20:57 PM >


_____________________________

Bob Brassell
Jett Engineering - Engine Mfg Support Forum Host

(in reply to RANIERY)
       Post #: 2

Page:   [1]
All Forums >> Glow Engines, Gas Engines, Fuel & Mfg Support Forums >> Engine Manufacturers Direct Support Forum >> Jett Engineering Support >> BSE 76
Page: [1]





Jump to:


Google 



Search | Marketplace | Event Calendar | Local Clubs | Magazine | Product Ratings | New Products | Discussion Forums

Photo Gallery | Member Video Posts | RCU Video Gallery | Instructor Search | Field|Track|Marina Search

Advertisers | Hobby Vendor Resources | Rate Manufacturers | Sign In/Sign Up

SITE MAP!   : :   FORUM RULES

© 2001 - 2007 24-7 RC, LLC, all rights reserved.

Charities we support that also need your help
Yorkie Rescue | Humane Society | ASPCA | Crohn's-Colitis America

Kaango.com Classifieds

0.313RCU1