RE: ****NITROMODELS REPLACEMENT PARTS REQUEST HERE *****  
View related threads: (in this forum | in all forums)

Tower Hobbies
Enter up to 4 keywords or Tower stock numbers
Logged in as Guest



Users viewing this topic: none
  Printable Version
       

All Forums >> RC Airplanes >> ARF or RTF >> NitroModels Support >> RE: ****NITROMODELS REPLACEMENT PARTS REQUEST HERE *****
Page: <<   < prev  11 12 13 14 [15] 16 17 18 19 20   next >   >>  

Login
Message << Older Topic   Newer Topic >>
RE: ****NITROMODELS REPLACEMENT PARTS REQUEST HERE ***** - 6/12/2008 2:54:23 AM   
margusity


 

Posts: 22
Joined: 8/14/2006
From: , PA, USA
Status: offline 		Hey

I did see a yak canopy you can order for your airplane.. Look here...

http://www.nitroplanes.com/cmparfaica.html

Henry

(in reply to FLFlyboy)
       Post #: 351

RE: ****NITROMODELS REPLACEMENT PARTS REQUEST HERE ***** - 6/13/2008 6:26:56 PM   
oneaew@msn.com


 

Posts: 56
Joined: 8/5/2002
From: hemet , CA, USA
Status: offline 		not looking for parts yet> but is the battery strong enough to fly this plane my just got 2 ft off the ground>when i got the plane the side of the body was cracked> the nose servo screws would not get tite> the glue is really bad did not dry good and i had to use epoxy if all your planes are like this one ill never buy another one>i guess u get what u pay for cheap cheap

(in reply to nitrostaff1)
       Post #: 352

RE: ****NITROMODELS REPLACEMENT PARTS REQUEST HERE ***** - 6/13/2008 9:11:51 PM   
elsabella


 

Posts: 33
Joined: 4/25/2004
From: myerstown, PA, USA
Status: offline 		I Need a aluminum wing bar for the cmpro giles 202 140. got one?

(in reply to nitrostaff1)
       Post #: 353

RE: ****NITROMODELS REPLACEMENT PARTS REQUEST HERE ***** - 6/13/2008 9:14:07 PM   
elsabella


 

Posts: 33
Joined: 4/25/2004
From: myerstown, PA, USA
Status: offline 		I Need a aluminum wing bar for the cmpro giles 202 140. got one? mine is bent

(in reply to nitrostaff1)
       Post #: 354

RE: ****NITROMODELS REPLACEMENT PARTS REQUEST HERE ***** - 6/16/2008 2:16:23 PM   
CRASH10


 

Posts: 47
Joined: 2/1/2005
From: Duluth, GA, USA
Status: offline 		Ok i baught a 120 size cub from you guys a few weeks ago. I started engine up to taxi around parking lot when the landing gear at the welds just came apart in one spot.Plane dropped like a rock and Broke prop.No problem right?Well so i put my own tack weld there thinking it was just a bad weld. Maiden the plane flew great and so as i landed guess what? All the welds except mine snapped and drove the whole cow into the ground and breaking the firewall!!!!! It's aparent that what they did was just barley even hit the parts with a weld trying to make it look nice and clean but there was absolutly no structual integrity what so ever...I know you guys had to know this! There is no way in hell that no one else has had this problem. But you sent it out to me anyway so now i paid $265.00 for one flight.Not to mention all the time i put into building it.....

_____________________________

CRASH WWW.WHITEKNUCKLEAIRLINES.com

(in reply to nitrostaff1)
       Post #: 355

RE: ****NITROMODELS REPLACEMENT PARTS REQUEST HERE ***** - 6/16/2008 2:29:07 PM   
CRASH10


 

Posts: 47
Joined: 2/1/2005
From: Duluth, GA, USA
Status: offline 		I guess they thaught i was gonna hang it from the ceiling in my bar......or maby put floats on it.....lol i don't know but the compant building the landing gear should be fired....Any company who puts that much effort into making such a sh%#*y product doesn't deserve my interest.......

_____________________________

CRASH WWW.WHITEKNUCKLEAIRLINES.com

(in reply to CRASH10)
       Post #: 356

RE: ****NITROMODELS REPLACEMENT PARTS REQUEST HERE ***** - 6/16/2008 2:46:00 PM   
BeanerECMO


 

Posts: 224
Joined: 5/20/2005
From: Springfield, VA, USA
Status: offline 		You might want to go to their chat line - it's the box in the upper right corner of their homepage.

(in reply to CRASH10)
       Post #: 357

RE: ****NITROMODELS REPLACEMENT PARTS REQUEST HERE ***** - 6/16/2008 2:56:38 PM   
truevine77


 

Posts: 17
Joined: 1/5/2007
From: , CT, USA
Status: offline 		I need a replacement fuselage for my Nitroplane Seawind. Thanks.

(in reply to BeanerECMO)
       Post #: 358

RE: ****NITROMODELS REPLACEMENT PARTS REQUEST HERE ***** - 6/16/2008 2:59:27 PM   
truevine77


 

Posts: 17
Joined: 1/5/2007
From: , CT, USA
Status: offline 		I need a replacement fuselage for my Nitroplane Seawind. Thanks.

(in reply to truevine77)
       Post #: 359

RE: ****NITROMODELS REPLACEMENT PARTS REQUEST HERE ***** - 6/16/2008 3:02:28 PM   
margusity


 

Posts: 22
Joined: 8/14/2006
From: , PA, USA
Status: offline 		The chat line is useless. It's just a computer that recommends the obvious by reading specific words in a sentence. It would be nice if a real person would answer the forum since it was set up by Nitroplanes.

H

(in reply to truevine77)
       Post #: 360

RE: ****NITROMODELS REPLACEMENT PARTS REQUEST HERE ***** - 6/16/2008 3:21:12 PM   
BeanerECMO


 

Posts: 224
Joined: 5/20/2005
From: Springfield, VA, USA
Status: offline 		It's not a computer, and I've resolved issues through it (Jason & Tammy) as well as one of their call-in numbers.

(in reply to margusity)
       Post #: 361

RE: ****NITROMODELS REPLACEMENT PARTS REQUEST HERE ***** - 6/16/2008 3:41:41 PM   
margusity


 

Posts: 22
Joined: 8/14/2006
From: , PA, USA
Status: offline 		It didn't resolve my issue, in fact, it just gave me an automated response. here's my issue, let me see if you can resolve it...

Do you have a canopy and fuselage for a

Nitro Models Extra 330 90 - 63" ARF 3D Aerobatic Nitro Gas Radio Remote Controlled RC Plane

I had a little accident and need new parts...


(in reply to albert burton)
       Post #: 362

RE: ****NITROMODELS REPLACEMENT PARTS REQUEST HERE ***** - 6/17/2008 8:38:03 AM   
wl7cpa


 

Posts: 29
Joined: 2/4/2006
From: Sarasota, FL, USA
Status: offline 		I need replacement tail wheels for the P-82 Twin Mustang. This is second request and no response to date.

(in reply to nitrostaff1)
       Post #: 363

RE: ****NITROMODELS REPLACEMENT PARTS REQUEST HERE ***** - 6/17/2008 1:20:47 PM   
margusity


 

Posts: 22
Joined: 8/14/2006
From: , PA, USA
Status: offline 		I am happy now. The tech phone number you gave me worked and I was able to order a new fuse and canopy. The guy on the phone was very nice. Thanks for your help....

(in reply to wl7cpa)
       Post #: 364

RE: ****NITROMODELS REPLACEMENT PARTS REQUEST HERE ***** - 6/19/2008 2:34:43 AM   
al_bundy


 

Posts: 1
Joined: 2/17/2005
From: Newton, IA, USA
Status: offline 		Need a landing gear for Giles 120, please.

(in reply to nitrostaff1)
       Post #: 365

RE: ****NITROMODELS REPLACEMENT PARTS REQUEST HERE ***** - 6/20/2008 4:31:36 AM   
heligaz


 

Posts: 2
Joined: 11/25/2007
From: Toronto, ON, CANADA
Status: offline 		I have a Nitro Models Yellow USAF BOBCAT 50 - 51" Nitro Gas Powered Radio Remote Control RC Airplane Jet Plane w/ RETRACT READY.

I cannot find or know if I got a manual for it.
please can you email the manual.

I have built quite a lot of it , but just want to make sure things are right.

Thanks

caingary@hotmail.com

(in reply to al_bundy)