OFFICIAL FORUM HOST - yadac123 (Full Version)

All Forums >> [RC Cars, Buggies, Trucks, Tanks and more] >> Exceed RC Support - Nitro Cars



Message

Nathan -> OFFICIAL FORUM HOST - yadac123 (1/22/2008 9:29:42 PM)

Andy (yadac123) from Exceed RC is here as the official Exceed RC forum host. He is dedicated to answering all your questions and supporting all Exceed RC products.



tokenring -> RE: OFFICIAL FORUM HOST - yadac123 (1/22/2008 10:33:52 PM)

Hey Andy! Welcome aboard!

AB



HimotoRacingUSA -> RE: OFFICIAL FORUM HOST - yadac123 (1/23/2008 12:10:58 AM)

Welcome Andy,

It will be good for exceed owners to have someone/someplace to turn to for support.



DonnyNitro -> RE: OFFICIAL FORUM HOST - yadac123 (1/23/2008 2:54:22 AM)

Hello Andy,
I bought an Exceed 1/10 Nitro Extreme Forza buggy and i love it. No problems with shipping when I ordered from Nitrorcx.com. Only problem was I didn't get an antenna tube when I got my car (a bendy straw worked). Other than that i love it.
Thanks,
Don



just2stoned -> RE: OFFICIAL FORUM HOST - yadac123 (1/23/2008 4:31:29 AM)

Howdy Andy.



yadac123 -> RE: OFFICIAL FORUM HOST - yadac123 (1/23/2008 6:08:44 AM)

Don,
I can help. Let me know your order number with nitrorcx and I'll send one to you.

Thanks
quote:

ORIGINAL: ldgasp

Hello Andy,
I bought an Exceed 1/10 Nitro Extreme Forza buggy and i love it. No problems with shipping when I ordered from Nitrorcx.com. Only problem was I didn't get an antenna tube when I got my car (a bendy straw worked). Other than that i love it.
Thanks,
Don




DonnyNitro -> RE: OFFICIAL FORUM HOST - yadac123 (2/4/2008 9:15:03 PM)

Andy, got my antenna tube today. thanks so much. i know its like $1.00 piecew but, you sending me one proves you are here to help. Thanks alot.



cute_mr2 -> RE: OFFICIAL FORUM HOST - yadac123 (2/6/2008 9:32:03 AM)

Hello Andy,
I bought an Exceed 1/10 Nitro buggy (and an electric track). I ordered it from Nitrorcx.com. I have a problem with nearly since i bought it is that i can get the engine to run good. the carburettor will not get tuned whatever you do.
to get the car to perform little bit you have to unwind the needle valve all the way out.and still the car will not perform in a normal way. i have removed the carburettor clean it put it back nothing..new glow plug...still nothing. the car hesitates at high and low rmp. i know how to tune the engines...i have helicopters ..planes....other nitro cars but is the only one giving me such carburettors problems.
any suggestion.?

Thanks,
JASON



yadac123 -> RE: OFFICIAL FORUM HOST - yadac123 (2/6/2008 10:02:10 PM)

so you engine starts but it quickley dies? Make sure your idle scew leaves a 2mm gap at idle. Full idle show not open all the way and 3 quarter is be ok.

Andy



cute_mr2 -> RE: OFFICIAL FORUM HOST - yadac123 (2/7/2008 8:54:19 AM)

The engine runs on idle with no problem. the problem is once you want the car to accelerate. I have other engines one other cars plane helis and i can tune them with no problem. this engine does not want to be tuned what ever you do to it. i have done all settings all test...the pinch test for the low screw...i have done the test if its leaking air...etc...everything but with no change. also i have noticed that when the engine gets to running temp and when using it for some time.....the high needle adjustment screw it becomes loose and rotates on its own. HELP...its getting really annoying. It run perfectly only for a couple of days since i got it... after that.....



yadac123 -> RE: OFFICIAL FORUM HOST - yadac123 (2/8/2008 2:17:50 AM)

In that case you can send the engine back and I'll replace you with another one.

Let me know
Andy



cute_mr2 -> RE: OFFICIAL FORUM HOST - yadac123 (2/8/2008 8:49:49 AM)

Thank you Andy.

But it want be easier just to sent the carburettor? Because i Live in Cyprus (small European island in the Mediterranean Sea) and will take some time for the engine to be sent back to the USA and then the new engine to be sent Back to Cyprus.

Please let me know what to do.



cute_mr2 -> RE: OFFICIAL FORUM HOST - yadac123 (2/12/2008 6:50:58 AM)

ANDY is LOST???



yadac123 -> RE: OFFICIAL FORUM HOST - yadac123 (2/13/2008 7:20:19 AM)

Sure. If you think that's the problem i'll do it. what's your order number?

Andy
quote:

ORIGINAL: cute_mr2

Thank you Andy.

But it want be easier just to sent the carburettor? Because i Live in Cyprus (small European island in the Mediterranean Sea) and will take some time for the engine to be sent back to the USA and then the new engine to be sent Back to Cyprus.

Please let me know what to do.




cute_mr2 -> RE: OFFICIAL FORUM HOST - yadac123 (2/13/2008 11:42:30 AM)

hey Andy

Thx for that. I have read other posts that more people are having problems with adjusting the carburetor.. and with the needle screw coming loose. i hope that the new one that you will sent does not have the same problem. cross our finger.
Another thing is the back left wheel bearing has come apart and i was wondering if you could sent a set of those bearings together with the carburetor and i will pay for those bearings. also i have seen that the have a steel exhaust for that engine but nitrorcx says that the item its out of stock..will it be possible to find one of those somewhere? if you can please let me know so i can get them sent all together
My order Number is: 244320

thank you for all the help



yadac123 -> RE: OFFICIAL FORUM HOST - yadac123 (2/13/2008 9:45:54 PM)

the alumin exhaust will be back instock soon. The high end needle has a rubber o-ring to obsorb the virbation and please make sure that o ring is still there. also if you can get me the part number for the part you needed

Thanks
Andy



cute_mr2 -> RE: OFFICIAL FORUM HOST - yadac123 (2/16/2008 3:17:51 PM)

i have changed the needle o ring with a new one but nothing.
the part numbers that i need are: 1 ) 2043 (brake cam) the top of the cam broke. 2) 2079 (oil bearing) i think that this is the part number for the bearing for rear outer hub assembly for rear wheel. it does not show on the drawings in the manual the part number for that bearing.



yadac123 -> RE: OFFICIAL FORUM HOST - yadac123 (2/18/2008 10:42:54 PM)

I can not find the 2 part you requested. I'll send you a carburator plus 2 parts. parts number starts with 51c00-

Andy
quote:

ORIGINAL: cute_mr2

i have changed the needle o ring with a new one but nothing.
the part numbers that i need are: 1 ) 2043 (brake cam) the top of the cam broke. 2) 2079 (oil bearing) i think that this is the part number for the bearing for rear outer hub assembly for rear wheel. it does not show on the drawings in the manual the part number for that bearing.




cute_mr2 -> RE: OFFICIAL FORUM HOST - yadac123 (2/19/2008 9:25:10 AM)

Andy
this are the correct part numbers
1) Brake Cam 51C00-02043
2) Ball Bearing 51C00-02138 (Is this is the part number for the bearing for rear outer hub assembly for rear wheel???)



tokenring -> RE: OFFICIAL FORUM HOST - yadac123 (2/19/2008 1:31:50 PM)

Hi Andy!

I received my spare rims and tires today in the mail. Thanks for that. I'll let you know about the colours when I open the box. I need to know something else from you too. Can you check my new thread.


Aaron



yadac123 -> RE: OFFICIAL FORUM HOST - yadac123 (2/21/2008 4:36:33 AM)

Your parts has been sent.

Andy
quote:

ORIGINAL: cute_mr2

Andy
this are the correct part numbers
1) Brake Cam 51C00-02043
2) Ball Bearing 51C00-02138 (Is this is the part number for the bearing for rear outer hub assembly for rear wheel???)




cute_mr2 -> RE: OFFICIAL FORUM HOST - yadac123 (2/21/2008 7:53:46 AM)

Thank you Andy.

you are a great help!



guy4x4 -> RE: OFFICIAL FORUM HOST - yadac123 (3/27/2008 1:54:57 PM)

Hi Andy I was on the nitrorcx website and seen the wild blue Exceed and wanted to know if I can buy the blue wheels that are on that truck here is a pic of the wheels I want thanks.
[IMG]http://i3.photobucket.com/albums/y77/GUYKORN/yhst-14197398381157_1994_39088589.jpg[/IMG]



guy4x4 -> RE: OFFICIAL FORUM HOST - yadac123 (3/28/2008 6:58:01 PM)

Simple answer yes or no im trying to give you business [:)]



yadac123 -> RE: OFFICIAL FORUM HOST - yadac123 (4/3/2008 12:02:24 AM)

Yes we'll carry blue wheels but now we do not have it. Sorry

once we have it instock we'll post on our site.

Andy



Page: [1] 2   next >   >>  

Valid CSS!




SITE MAP!   : :   FORUM RULES

© 2001 - 2007 24-7 RC, LLC, all rights reserved.
0.3588867