HS-645MG's versus HS625MG's on a Cermark SU-31- torque vs. speed?  
View related threads: (in this forum | in all forums)

Tower Hobbies
Enter up to 4 keywords or Tower stock numbers
Logged in as Guest



Users viewing this topic: none
  Printable Version
       



All Forums >> Radios, Batteries, Clubhouse and more >> RC Radios, Transmitters, Receivers, Servos, gyros >> Radio Manufacturer Direct Support >> Hitec/MultiPlex Radios- Ask Hitec Customer Service >> HS-645MG's versus HS625MG's on a Cermark SU-31- torque vs. speed? Page: [1]

Login
Message << Older Topic   Newer Topic >>
HS-645MG's versus HS625MG's on a Cermark SU-31- torque ... - 4/11/2008 11:02:36 AM   
root



Posts: 451
Joined: 11/20/2004
From: Manasquan, NJ, USA
Status: offline 		I'm planning on the Cermark rep's recommended HS-625mg's for the ailerons and two 645MG's in the tail of their newest 2nd version Cermark 9.?lb Sukhoi 31.

A 69 inch wingspan with aerobat/3D expected performance w/ a G23 in the nose

The slowness of the 645's at just .20/second@6v (torque is 133@6v or107@4.8v) is bothering me.

Does anyone think it's gonna make a big difference if the 625's (.13sec and 94oz.) are used all around being that their way fa.ster and only 13oz. less torque if ran at 6Volts
or
Am I better off going with the higher torque and less speed?



< Message edited by root -- 4/11/2008 11:06:26 AM >

_____________________________

"I should have zigged instead of zagged"
       Post #: 1

RE: HS-645MG's versus HS625MG's on a Cermark SU-31- to... - 4/11/2008 8:54:01 PM   
MikeMayberry



Posts: 2823
Joined: 1/15/2002
From: Poway, CA, USA
Status: offline 		Typically the 645's are plenty fast enough for 3D flying. If you want better performance I would suggest the digital version (5625/5645) or better yet, step up to the coreless motor 985MG or digital 5985MG.

Mike.

_____________________________

Hitec RCD Rep
http://www.hitecrcd.com

(in reply to root)
       Post #: 2

RE: HS-645MG's versus HS625MG's on a Cermark SU-31- to... - 4/11/2008 11:24:15 PM   
root



Posts: 451
Joined: 11/20/2004
From: Manasquan, NJ, USA
Status: offline 		Do you think the 625's have the strentgth to handle the rudder or elevator if I run them at 6volts.....even though there's a 13oz/ft difference?

_____________________________

"I should have zigged instead of zagged"

(in reply to MikeMayberry)
       Post #: 3

RE: HS-645MG's versus HS625MG's on a Cermark SU-31- to... - 4/12/2008 1:59:51 AM   
root



Posts: 451
Joined: 11/20/2004
From: Manasquan, NJ, USA
Status: offline 		I don't wanna spend the $$ for the digitals.

I hope you don't mind but i presented this question on the 3D forums for more opinions from more 3D guys just to see if they agree.

Thanks for your time, Mike.

_____________________________

"I should have zigged instead of zagged"

(in reply to MikeMayberry)
       Post #: 4

RE: HS-645MG's versus HS625MG's on a Cermark SU-31- to... - 4/14/2008 6:44:29 PM   
MikeMayberry



Posts: 2823
Joined: 1/15/2002
From: Poway, CA, USA
Status: offline 		I''d probably go with the 645 for the rudder, but the 625''s should be fine for the elevator and ailerons.

Mike.

_____________________________

Hitec RCD Rep
http://www.hitecrcd.com

(in reply to root)
       Post #: 5

RE: HS-645MG's versus HS625MG's on a Cermark SU-31- to... - 4/14/2008 8:39:31 PM   
root



Posts: 451
Joined: 11/20/2004
From: Manasquan, NJ, USA
Status: offline 		The Cermark rep said to go with the 645 on the elevator since it uses a single servo and a rod that connects the 2 sides together. I questioned the elevator recomendation myself cuz the usual stronger servo in the rudder is the norm.

_____________________________

"I should have zigged instead of zagged"

(in reply to MikeMayberry)
       Post #: 6

RE: HS-645MG's versus HS625MG's on a Cermark SU-31- to... - 4/15/2008 6:34:45 PM   
MikeMayberry



Posts: 2823
Joined: 1/15/2002
From: Poway, CA, USA
Status: offline 		Sorry, I was assuming it had one servo per elevator half.... yes, the 645 would be a better choice.

Mike.

_____________________________

Hitec RCD Rep
http://www.hitecrcd.com

(in reply to root)
       Post #: 7

RE: HS-645MG's versus HS625MG's on a Cermark SU-31- to... - 4/15/2008 8:07:07 PM   
root



Posts: 451
Joined: 11/20/2004
From: Manasquan, NJ, USA
Status: offline 		Alrighty then!

That''s my final decision.

Thanks

_____________________________

"I should have zigged instead of zagged"

(in reply to MikeMayberry)
       Post #: 8

Page:   [1]
All Forums >> Radios, Batteries, Clubhouse and more >> RC Radios, Transmitters, Receivers, Servos, gyros >> Radio Manufacturer Direct Support >> Hitec/MultiPlex Radios- Ask Hitec Customer Service >> HS-645MG's versus HS625MG's on a Cermark SU-31- torque vs. speed?
Page: [1]





Jump to:


Google 



Search | Marketplace | Event Calendar | Local Clubs | Magazine | Product Ratings | New Products | Discussion Forums

Photo Gallery | Member Video Posts | RCU Video Gallery | Instructor Search | Field|Track|Marina Search

Advertisers | Hobby Vendor Resources | Rate Manufacturers | Sign In/Sign Up

SITE MAP!   : :   FORUM RULES

© 2001 - 2007 24-7 RC, LLC, all rights reserved.

Charities we support that also need your help
Yorkie Rescue | Humane Society | ASPCA | Crohn's-Colitis America

Kaango.com Classifieds

0.500RCU1