Assembling Slimline Pro cap-help needed  
View related threads: (in this forum | in all forums)

Tower Hobbies
Enter up to 4 keywords or Tower stock numbers
Logged in as Guest



Users viewing this topic: none
  Printable Version
       


XYZ-26cc Gas Engine
Seller:  XYZUSA
Details:   $219.00   |  4/26/2008   |  Classified Ad
We will rotate YOUR AD in this spot if you select "Forum Featured" when placing or editing your ad!

All Forums >> Glow Engines, Gas Engines, Fuel & Mfg Support Forums >> RC Fuels >> Assembling Slimline Pro cap-help needed
Page: [1]

Login
Message << Older Topic   Newer Topic >>
Assembling Slimline Pro cap-help needed - 4/29/2008 2:24:45 AM   
niche



Posts: 111
Joined: 3/27/2002
From: Bogota, COLOMBIA
Status: offline 		During the past week I got one F1 pro cap can (2528
F1 Pro Cap Can ) via tower hobbies.
The product looks awesome but I have not been able to put together the puzzle.
I mean it has o-rings, washers and fittings but I could not figure out the way to put together the whole thing and I have not seen any of those on my flying field.
I would appreciate if anyone can help me with any assembly instructions or hand write sketches so I can get it to work.
Thanks in advance
Omar
       Post #: 1

RE: Assembling Slimline Pro cap-help needed - 4/30/2008 9:04:14 PM   
David B



Posts: 58
Joined: 2/23/2002
From: Warren, NJ, USA
Status: offline 		Omar,

The large orange o-ring goes inside the cap and sits as deep in the cap as possible, in the inside corners. It's purpose is to seal the cap to the jug. The other orange o-ring goes on the fuel tip in the groove. It's purpose is to seal the fuel tip when inserted in the fuel cap. The black o-ring also goes on the fuel tip. It sits in the large groove at the top. It's just for grabbing the fuel tip. The white washers go between the cap & the 10-32 fuel fittings (fuel nipples that you attach the fuel tubing to). I'm not sure why there's 4 washers as it appears you only need 2. If you need further help you might drop slimline a note or call them directly. www.slimlineproducts.com email: support@slimlineproducts.com

Hope this helps.

David B

(in reply to niche)
       Post #: 2

RE: Assembling Slimline Pro cap-help needed - 5/3/2008 2:40:51 AM   
niche



Posts: 111
Joined: 3/27/2002
From: Bogota, COLOMBIA
Status: offline 		Thanks David
It looks like you got the same assembly I did
The cap has two holes, one wider than the other, The fittings don't pass through so I don't know how to plug the tubing.
could you by any chance send me a picture of the thing to see how it's put together.
I have sent two e-mail's to Slimline, , no luck so far they have not even replied once which is frustrating, the sell things with no instructions and don't try to help customers either.
Regards
Omar

(in reply to David B)
       Post #: 3

Page:   [1]
All Forums >> Glow Engines, Gas Engines, Fuel & Mfg Support Forums >> RC Fuels >> Assembling Slimline Pro cap-help needed
Page: [1]





Jump to:


Google 



Search | Marketplace | Event Calendar | Local Clubs | Magazine | Product Ratings | New Products | Discussion Forums

Photo Gallery | Member Video Posts | RCU Video Gallery | Instructor Search | Field|Track|Marina Search

Advertisers | Hobby Vendor Resources | Rate Manufacturers | Sign In/Sign Up

SITE MAP!   : :   FORUM RULES

© 2001 - 2007 24-7 RC, LLC, all rights reserved.

Charities we support that also need your help
Yorkie Rescue | Humane Society | ASPCA | Crohn's-Colitis America

Kaango.com Classifieds

0.406RCU1