Infinity truck questions please help! (Full Version)

All Forums >> [RC Cars, Buggies, Trucks, Tanks and more] >> Exceed RC Support - Nitro Cars



Message

dc419 -> Infinity truck questions please help! (5/1/2008 7:32:08 PM)

whats up everyone... i just bought a 1/10 scale infinity because i recently broke my collarbone and had to have surgery ( bike accident ) anyway i need to jump somthing ya know and the infinity is somthing i can afford only being 16 and all so im a newbie to the rc hobby and im wondering if you guys would help me out just maybe let me in on a few tips just anything whatever you think i should know and also how to properly break in the motor because i have no clue how too, and also did i make the right decision buying this truck or is it just going to break the first jump i send it flying off??? thanks for all the help guys and im looking forward to being apart of the exceed rc club or whatever lol [:)]



tihstae -> RE: Infinity truck questions please help! (5/1/2008 10:09:56 PM)

i have this truck and love it, the only time i broke anything was when i hit curbs and stuff in the beginning. they are tuff but not unbreakable haha. you can watch videos to learn how to break an engine in and tune and stuff, people have different theories on breakin in engines, i just drove around going and stopping and doing what the manual said, and it worked.



yadac123 -> RE: Infinity truck questions please help! (5/2/2008 2:02:05 PM)

When you break in your engine you need to set the low end needle to flush with the silver collar. High end needle should be turn inward full and 2.5 turn back out.

Andy



AllAboutFunHobbies -> RE: Infinity truck questions please help! (5/6/2008 5:07:06 AM)

FOr the break in use the traxxas break in procedure, you can find that on the traxxas website and I would start with it 3 full out on the highspeed and work from there by 1/8th incraments. turning the VX HSP needle to 2.5 turns out is getting close too to lean and it will run hot.



yadac123 -> RE: Infinity truck questions please help! (5/7/2008 3:16:20 PM)

what about LSP flush with silver collar? do you think that's good?

Andy

quote:

ORIGINAL: AllAboutFunHobbies

FOr the break in use the traxxas break in procedure, you can find that on the traxxas website and I would start with it 3 full out on the highspeed and work from there by 1/8th incraments. turning the VX HSP needle to 2.5 turns out is getting close too to lean and it will run hot.




{GBI}Harryball -> RE: Infinity truck questions please help! (5/7/2008 3:31:52 PM)


quote:

ORIGINAL: yadac123

what about LSP flush with silver collar? do you think that's good?

Andy

quote:

ORIGINAL: AllAboutFunHobbies

FOr the break in use the traxxas break in procedure, you can find that on the traxxas website and I would start with it 3 full out on the highspeed and work from there by 1/8th incraments. turning the VX HSP needle to 2.5 turns out is getting close too to lean and it will run hot.




Yea Andy the LSN should be flush with the collar



AllAboutFunHobbies -> RE: Infinity truck questions please help! (5/7/2008 8:36:28 PM)


quote:

ORIGINAL: yadac123

what about LSP flush with silver collar? do you think that's good?

Andy

quote:

ORIGINAL: AllAboutFunHobbies

FOr the break in use the traxxas break in procedure, you can find that on the traxxas website and I would start with it 3 full out on the highspeed and work from there by 1/8th incraments. turning the VX HSP needle to 2.5 turns out is getting close too to lean and it will run hot.




If it's not flush with the collar during break in you"ll be running to lean on the low side and burn up the motor.



Page: [1]

Valid CSS!




SITE MAP!   : :   FORUM RULES

© 2001 - 2007 24-7 RC, LLC, all rights reserved.
0.09375