Why does it............    Gallery
View related threads: (in this forum | in all forums)

Logged in as Guest



Users viewing this topic: none
    Search This Thread  
 
Printable Version



All Forums >> RC Cars, Buggies, Trucks, Tanks and more >> Redcat Racing Support >> Why does it............
Page: [1]

Tower Hobbies Get Coupon Codes Brands  
Login
Message << Older Topic   Newer Topic >>
Why does it............ - 5/2/2008 2:19 AM   
schlags62


 

Posts: 522
Score: 100
Joined: 3/1/2007
Last Login: 3/26/2012
From: north platte, NE, USA
Status: offline 		Why does my clutch bell keep sliding up off of the clutches, the bolt that hold it on is tight and as soon as I put it all back together and run it a couple of minutes it slids up and makes the mesh only about half the gear.

_____________________________

Go BIG or go home! 110%

Hide Signatures
       Post #: 1

RE: Why does it............ - 5/2/2008 4:58 PM   
schlags62


 

Posts: 522
Score: 100
Joined: 3/1/2007
Last Login: 3/26/2012
From: north platte, NE, USA
Status: offline 		Nobody else has this problem with their Monsoon?

_____________________________

Go BIG or go home! 110%

Hide Signatures

(in reply to schlags62)
       Post #: 2

RE: Why does it............ - 5/2/2008 5:00 PM   
Chubbysdad


 

Posts: 2824
Score: 100
Joined: 6/24/2005
Last Login: 12/22/2009
From: Clermont, FL, USA
Status: offline 		check and see if there is a washer on the outside. For some reason some come without and even if the screw is tight, the clutchbell will slide right over the screw because there is no washer holding it on.

_____________________________

Cen truggy, Bigfoot 1/5th, Cen buggy, Mg16, Redcat Earthquake, Redcat Drifter

Hide Signatures

(in reply to schlags62)
       Post #: 3

RE: Why does it............ - 5/2/2008 7:04 PM   
AllAboutFunHobbies



Posts: 3096
Score: 100
Joined: 12/5/2006
Last Login: 11/10/2011
From: Euless, TX, USA
Status: offline
quote:

ORIGINAL: schlags62

Why does my clutch bell keep sliding up off of the clutches, the bolt that hold it on is tight and as soon as I put it all back together and run it a couple of minutes it slids up and makes the mesh only about half the gear.



If there is no washer at the end of the clitch bell you can get one at the hardware store for a couple cents, BUT make sure there is a small portion of the inside shaft sticking out, just a tiny bit, so that when you put the washer on and lock down the bolt, using lock tight, it doesn't seat against the end of the clutch bell. Other wise you will lock down the clutch bell too.

_____________________________

Dealer for..Redcat, Traxxas, Associated, Cen, Racers Edge, RD Logic, Losi, HPI, E-flight, Himoto, Venom, Heli-Max, O.S...etc

Hide Signatures

(in reply to schlags62)
       Post #: 4



Page:   [1]
All Forums >> RC Cars, Buggies, Trucks, Tanks and more >> Redcat Racing Support >> Why does it............
Page: [1]





Jump to:


 
Google 



Search | Marketplace | Event Calendar | Local Clubs | Magazine | Product Ratings | New Products | Discussion Forums

Photo Gallery | Instructor Search | Field|Track|Marina Search

Advertisers | Hobby Vendor Resources | Rate Manufacturers | Sign In/Sign Up

SITE MAP!   : :   FORUM RULES

RC Universe is a service of Internet Brands, Inc. Copyright © 2001-2013.

Charities we support that also need your help
Yorkie Rescue | Humane Society | ASPCA | Crohn's-Colitis America


0.156RCU1