DX6,GY401 and gain, help please.... (Full Version)

All Forums >> [RC Helicopters] >> RC Helicopter General Discussions



Message

FlyingHigh 400 -> DX6,GY401 and gain, help please.... (5/2/2008 9:41:20 AM)

I just finished all my settings but im lost on how to get to the gain settings for my gyro.How do I get to the settings for the gyro gain?I know I have to re-bind after turning the gain up or down but I cant find the settings to do that.I know my hitec gyro gain was at 72% and never had tail wag .How do I get the gyro gain at 72% with the DX6?

I have it set like the manual says (aileron D/R switch) but how do I adjust it?



planepounder -> RE: DX6,GY401 and gain, help please.... (5/2/2008 12:48:34 PM)

hey I have a DX6i, and the gyro is off the flap switch, if you assign the aileron d/r to gyro, what do you do about the alieron rates? On the 6i you use the flap switch. The 6i is a snap to set up on gyro, I thought the 6 would be similar. On the 6i the gyro adjust is inhibited until you enable it is the 6 the same? if so have you enabled it?



Skarn -> RE: DX6,GY401 and gain, help please.... (5/2/2008 1:18:08 PM)

Hey bro,

It depends on what channel you have setup for your gyro. Did you assign the GEAR > GEAR or GEAR > GYRO?

If you did the GEAR > GEAR you use your gear channel ATVs (end points) to set the gain. Anything over 50% is HH mode, under 50% is rate

If you did the GEAR > GYRO, you will have a new menu in the radio called gyro sense. Set that to F.MODE Auto. Then you will be able to program gain for both ST0: ST1:
Set the gain to 72% as a starting point....I did as per the Finless vids and haven't ever had to change it.

Remember, anything over 50% is HH mode, under 50% is rate.

Good luck!
Skarn



FlyingHigh 400 -> RE: DX6,GY401 and gain, help please.... (5/2/2008 10:38:36 PM)

Thanks for the help,but im still lost lol.It took me about 1 week to learn how to set my Hitec eclipse 7 up and it really helped with setting the DX6 up but im soooo lost on setting the gyro up so I can change the gain.I didnt think finless had a video on setting the DX6 up so im hunting it down now...



quote:

ORIGINAL: Skarn

Hey bro,

It depends on what channel you have setup for your gyro. Did you assign the GEAR > GEAR or GEAR > GYRO?

If you did the GEAR > GEAR you use your gear channel ATVs (end points) to set the gain. Anything over 50% is HH mode, under 50% is rate

If you did the GEAR > GYRO, you will have a new menu in the radio called gyro sense. Set that to F.MODE Auto. Then you will be able to program gain for both ST0: ST1:
Set the gain to 72% as a starting point....I did as per the Finless vids and haven't ever had to change it.

Remember, anything over 50% is HH mode, under 50% is rate.

Good luck!
Skarn




noobflyer01 -> RE: DX6,GY401 and gain, help please.... (5/10/2008 1:04:30 AM)

hey guys i have the dx6. the GER is at +65%. when i fly in normal mode it is fine. when i flip the idle up switch the tail wags alot. when i checked the tx to see what value is the GER in idle up and it is at -100%. how do i adjust it to make the tail steady in idle up? i'm using the gy401 with the futuba 9650 tail servo.



Page: [1]

Valid CSS!




SITE MAP!   : :   FORUM RULES

© 2001 - 2007 24-7 RC, LLC, all rights reserved.
0.109375