JR 7202 Programming for Nexus .30  
View related threads: (in this forum | in all forums)

Tower Hobbies
Enter up to 4 keywords or Tower stock numbers
Logged in as Guest



Users viewing this topic: none
  Printable Version
       

All Forums >> RC Helicopters >> Kyosho Helicopters >> JR 7202 Programming for Nexus .30
Page: [1]

Login
Message << Older Topic   Newer Topic >>
JR 7202 Programming for Nexus .30 - 7/13/2008 6:02:12 PM   
gpclassic


 

Posts: 15
Joined: 4/26/2007
From: Schenectady, NY, USA
Status: offline 		Hi guys
I'm having trouble Programming my JR 7202 to one of my Nexus .30's
I Have the Channel,modulation,Freq,and servo's in there but It's not right
The only time I can get the Swash Level is at 1/2 Throttle
when I raise the Throttle or lower it the Swash tips back and forth
This is what's not right
I've tried to switch the Swash Type and adjust the Sub Trim and it's still Not Right
The swash shouldn't tip when Moving the Throttle and I'm at a Loss as what to do now
I have been Messing with the Settings for Days and Can't figure this out and the Manual is not Helping me figure this out
Please HELP
Thanks
Rich D......
       Post #: 1

RE: JR 7202 Programming for Nexus .30 - 7/16/2008 6:43:48 PM   
evilhorse


 

Posts: 407
Joined: 11/7/2005
From: Woodbridge, NJ, USA
Status: offline 		ok first off set the swash to standard 1 servo, second: the swash should be level at left stick's center, with 0 degrees of pitch on the blades. Start there.

_____________________________

Life is short, fly HARD

(in reply to gpclassic)
       Post #: 2

RE: JR 7202 Programming for Nexus .30 - 7/30/2008 4:27:31 AM   
gpclassic


 

Posts: 15
Joined: 4/26/2007
From: Schenectady, NY, USA
Status: offline 		OK I got all that straightened out
the Tail servo is still fluttering Like Mad
The Gyro is an old 501 with a 9253 Digital Servo
I tried to change the frame rate setting, from high to norm and it's still fluttering like Mad
I even tried to set up another Heli into the JR 7202 Tx. and the other heli has a GY 401 on it, and it too is fluttering
and the led on the 401 is blinking and it won't initalize at all
do you guys have any suggestions ???

(in reply to evilhorse)
       Post #: 3

RE: JR 7202 Programming for Nexus .30 - 7/30/2008 4:05:36 PM   
evilhorse


 

Posts: 407
Joined: 11/7/2005
From: Woodbridge, NJ, USA
Status: offline 		sounds like A: you used trim to center it, B: your initializing in Rate mode which wont work. C: Your gain is way out of whack. BTW, do you have the gyro set to digital servo (DS on the Gyro)

_____________________________

Life is short, fly HARD

(in reply to gpclassic)
       Post #: 4

RE: JR 7202 Programming for Nexus .30 - 7/31/2008 4:17:11 AM   
gpclassic


 

Posts: 15
Joined: 4/26/2007
From: Schenectady, NY, USA
Status: offline 		I didn't use any trim at all
How do I tell if it's in Rate Mode ??

as Far as I can tell the Gain is at Zero

How do I tell if it's set for a Digital Mode

I'm not messing around
I've never Programmed a Tx Before this
and it's a Real Mystery top me as to what the Hell is going on

I would appreciate any help you can Give me at this point
Thanks
Rich D

(in reply to evilhorse)
       Post #: 5

RE: JR 7202 Programming for Nexus .30 - 8/1/2008 11:36:37 PM   
gpclassic


 

Posts: 15
Joined: 4/26/2007
From: Schenectady, NY, USA
Status: offline 		Hey Evilhorse any suggestions ???
Please HELP ME OUT
Thanks
GP

(in reply to gpclassic)
       Post #: 6

RE: JR 7202 Programming for Nexus .30 - 8/3/2008 4:28:15 PM   
evilhorse


 

Posts: 407
Joined: 11/7/2005
From: Woodbridge, NJ, USA
Status: offline 		I have no experience setting up a 501 although if i had it here i probably could.

http://www.roboticunicycle.info/documents/gy501-manual.pdf


Hey barracudahockey you think you could help me here?

_____________________________

Life is short, fly HARD

(in reply to gpclassic)
       Post #: 7

RE: JR 7202 Programming for Nexus .30 - 8/4/2008 12:13:28 AM   
gpclassic


 

Posts: 15
Joined: 4/26/2007
From: Schenectady, NY, USA
Status: offline 		I don't think it's the 501 I think somethins up with the JR 7202 I tried to put another Heli in to it and It's doing the Same thing

The other Heli Has a 401 and the LED'S Blinking and it won't initalize and the Tail servo is doing the Same thing

Thanks for the Link

GP

(in reply to evilhorse)
       Post #: 8

RE: JR 7202 Programming for Nexus .30 - 8/4/2008 4:34:40 PM   
evilhorse


 

Posts: 407
Joined: 11/7/2005
From: Woodbridge, NJ, USA
Status: offline 		ok its blinking either A: it's not in heading hold when you power up, or B: you hit the rudder trim in heading hold and it is reading that as a command.

on the 7202, go to channel assignments section, set Gear to Gear.
this will be your switch for rate mode to heading hold.
Plug the single wire plug from the GY401 into GEAR on the reciever, the other lead goes to rudder. set the ATV's on the gear channel to control your gain, the ATV's on rudder should be set to Left 85% right 110% thats just a baseline for pirouette rate, adjust to your liking later.

try this and then we'll go through tail setup later. lemme kn ow how it works

_____________________________

Life is short, fly HARD

(in reply to gpclassic)
       Post #: 9

Page:   [1]
All Forums >> RC Helicopters >> Kyosho Helicopters >> JR 7202 Programming for Nexus .30
Page: [1]





Jump to:


Google 



Search | Marketplace | Event Calendar | Local Clubs | Magazine | Product Ratings | New Products | Discussion Forums

Photo Gallery | Member Video Posts | RCU Video Gallery | Instructor Search | Field|Track|Marina Search

Advertisers | Hobby Vendor Resources | Rate Manufacturers | Sign In/Sign Up

SITE MAP!   : :   FORUM RULES

© 2001 - 2007 24-7 RC, LLC, all rights reserved.

Charities we support that also need your help
Yorkie Rescue | Humane Society | ASPCA | Crohn's-Colitis America

Kaango.com Classifieds

0.922RCU1