WK-G011 & TX    Gallery
View related threads: (in this forum | in all forums)

Logged in as Guest



Users viewing this topic: none
    Search This Thread  
 
Printable Version



All Forums >> RC Helicopters >> Exceed RC Support - Helicopter >> WK-G011 & TX
Page: [1]

Tower Hobbies Get Coupon Codes Brands  
Login
Message << Older Topic   Newer Topic >>
WK-G011 & TX - 1/15/2010 3:12 AM   
doogietim02


 

Posts: 19
Score: 100
Joined: 9/19/2009
Last Login: 5/25/2010
From: Sylvania, OH, USA
Status: offline 		 I have a WK-G011 DS gyro with my G2 along with a WK-2601 (non LCD ) Tx.  When it initializes all is well, however, the gyro's led has a slow flash.  Accordingly this probably means that the gyro is not receiving a signal from the Tx.  The receiver is the RX-2701.  Looking for some help in correcting this problem.  Is is correctable or is the gyro broke.  I tried hooking up a WK-G007 and it seemed to work just fine.

Thanks for any input

Tim

Hide Signatures
       Post #: 1

RE: WK-G011 & TX - 1/16/2010 2:39 AM   
yadac123


 

Posts: 1484
Score: 100
Joined: 9/17/2005
Last Login: 9/17/2010
From: , CA, USA
Status: offline 		when the gyro has a slow flash it means you have changed the initial position of the gyro after you it initliaze with the radio by moving the rudder trim.

first of all can you make sure the TX and rx is really communicating by testing it with a servo. Connect the gyro to ch4 and the gain wire to aux1 and pay attention to the polarity of the wires.

Andy

_____________________________

Andy - Official Exceed RC Support Forum Host

Hide Signatures

(in reply to doogietim02)
       Post #: 2

RE: WK-G011 & TX - 1/20/2010 5:50 AM   
doogietim02


 

Posts: 19
Score: 100
Joined: 9/19/2009
Last Login: 5/25/2010
From: Sylvania, OH, USA
Status: offline 		Thanks Andy, that worked.  Now the issue I have is with the left control stick.   When I move the stick to increase the throttle, it powers up nicely but no lift.  I noticed that the gyro that controls the pitch does not move upward with increasing throttle.  It actually moves downward with increasing throttle.  how can I correct this?  I am using the wk-2601 Tx and 2701 Rx.    I did try using a wk-701 with the appropriate rx and it worked just fine.  I would just like to get the 2601 working correctly.

thanks
Tim

Hide Signatures

(in reply to yadac123)
       Post #: 3

RE: WK-G011 & TX - 1/20/2010 5:51 AM   
doogietim02


 

Posts: 19
Score: 100
Joined: 9/19/2009
Last Login: 5/25/2010
From: Sylvania, OH, USA
Status: offline 		Also to add,  is there a factory default setting for the 2601? in regards to the back pins.

Tim

Hide Signatures

(in reply to doogietim02)
       Post #: 4

RE: WK-G011 & TX - 1/22/2010 4:14 AM   
yadac123


 

Posts: 1484
Score: 100
Joined: 9/17/2005
Last Login: 9/17/2010
From: , CA, USA
Status: offline 		ok if your heli doesn't lift that means the pitch is off and not set correctly. you want to turn on the heli and disconnect the main motor from the ESC. Throttle up and check your pitch.
Does the pitch servo moves up?

Andy

_____________________________

Andy - Official Exceed RC Support Forum Host

Hide Signatures

(in reply to doogietim02)
       Post #: 5

RE: WK-G011 & TX - 1/22/2010 6:11 AM   
doogietim02


 

Posts: 19
Score: 100
Joined: 9/19/2009
Last Login: 5/25/2010
From: Sylvania, OH, USA
Status: offline 		Okay, here is what happens.  When I push left stick forward, the pitch shaft goes down.  When I pull the left stick back down, the pitch shaft goes up.  The right stick forward makes the swash plate rocker rock backwards and pulling the right stick down moves the rocker forward.  I compared this to my other G2 and it appears that the left  stick functions are opposite.  My other G2 the left stick forward gives throttle up and pitch shaft up like it should. 

The rudder control appears to be ok.  Move the stick left makes the slider on the shaft move right or  outward from the tail and vice versa.

What do you think?

Tim

ps  the pin settings on thew back are as follows: 2,4,6,8 and 9 are all on.   This is the WK-2601 (non lcd) tx. with the 2701 receiver.

< Message edited by doogietim02 -- 1/26/2010 3:13 PM >

Hide Signatures

(in reply to yadac123)
       Post #: 6

RE: WK-G011 & TX - 1/28/2010 3:58 AM   
yadac123


 

Posts: 1484
Score: 100
Joined: 9/17/2005
Last Login: 9/17/2010
From: , CA, USA
Status: offline 		I think your dip switch settings are wrong and that's why your pitch is set incorrectly. 2 4 6 7 ON rest are all off.

Let me know.

Andy

_____________________________

Andy - Official Exceed RC Support Forum Host

Hide Signatures

(in reply to doogietim02)
       Post #: 7

RE: WK-G011 & TX - 1/28/2010 4:22 AM   
doogietim02


 

Posts: 19
Score: 100
Joined: 9/19/2009
Last Login: 5/25/2010
From: Sylvania, OH, USA
Status: offline 		Thanks Andy.  I just tried as you said with dip switches.  No cahange.  With left stick forward, the pitch shaft goes down.  Looking directly at the servo from the opposite side its on, when I move the left stick forward, the servo moves counterclockwise.  Bringing the stick back down moves the servo back clockwise. Thus no increase in pitch with throttle up.

Tim

Hide Signatures

(in reply to yadac123)
       Post #: 8

RE: WK-G011 & TX - 1/28/2010 7:44 AM   
yadac123


 

Posts: 1484
Score: 100
Joined: 9/17/2005
Last Login: 9/17/2010
From: , CA, USA
Status: offline 		did you remove this servo and replace it with another servo? You might installed the servo in the opposite direction.

Andy

_____________________________

Andy - Official Exceed RC Support Forum Host

Hide Signatures

(in reply to doogietim02)
       Post #: 9

RE: WK-G011 & TX - 1/28/2010 1:00 PM   
doogietim02


 

Posts: 19
Score: 100
Joined: 9/19/2009
Last Login: 5/25/2010
From: Sylvania, OH, USA
Status: offline 		Yes I already tried that.  I actually tried three different servos.  Also, there is only one way to install this servo.  Any other way and the arm won't reach.  Is it possible the tx has an adjustable feature where you can change the polarity of the receiver making the servo turn a diiferent direction.   As in my situation, so the servo turns clockwise with a forward stick?   Is it possible the rx is malfuntioning?  however, all other funtions with the receiver are just fine.
 Does this tx have the ability to reverse a servo and maybe that is what the problem is?


doogietim02

< Message edited by doogietim02 -- 1/28/2010 9:45 PM >

Hide Signatures

(in reply to yadac123)
       Post #: 10

RE: WK-G011 & TX - 1/30/2010 3:49 AM   
yadac123


 

Posts: 1484
Score: 100
Joined: 9/17/2005
Last Login: 9/17/2010
From: , CA, USA
Status: offline 		No problem with TX, it just that your setting are off.

ok try this. 1 2 4 6 ON and rest are all off.

make sure this pitch servo is connected to aux1 on the receiver.

Let me know

Andy

_____________________________

Andy - Official Exceed RC Support Forum Host

Hide Signatures

(in reply to doogietim02)
       Post #: 11

RE: WK-G011 & TX - 1/30/2010 4:50 AM   
doogietim02


 

Posts: 19
Score: 100
Joined: 9/19/2009
Last Login: 5/25/2010
From: Sylvania, OH, USA
Status: offline 		Thanks for being quick..  OK.  I tried as you suggested and made sure it is in aux 1 but no difference.  Pitch shaft still goes down ( servo moves counterclockwise)

doogietim02

Hide Signatures

(in reply to yadac123)
       Post #: 12

RE: WK-G011 & TX - 2/4/2010 4:02 AM   
yadac123


 

Posts: 1484
Score: 100
Joined: 9/17/2005
Last Login: 9/17/2010
From: , CA, USA
Status: offline 		I emailed you a new setting and I believe you got it working....I'm not sure. Let me know.

Andy

_____________________________

Andy - Official Exceed RC Support Forum Host

Hide Signatures

(in reply to doogietim02)
       Post #: 13

RE: WK-G011 & TX - 2/4/2010 4:21 AM   
doogietim02


 

Posts: 19
Score: 100
Joined: 9/19/2009
Last Login: 5/25/2010
From: Sylvania, OH, USA
Status: offline

As I mentioned before, YOU ARE THE MAN,  Andy.  That last setting was perfect.  I have not had a chance to fly it yet due to the weather but the servo is now clockwise and works correctly.

  Thanks Again

Doogietim02



Hide Signatures

(in reply to yadac123)
       Post #: 14

RE: WK-G011 & TX - 2/6/2010 4:18 AM   
yadac123


 

Posts: 1484
Score: 100
Joined: 9/17/2005
Last Login: 9/17/2010
From: , CA, USA
Status: offline

Andy

_____________________________

Andy - Official Exceed RC Support Forum Host

Hide Signatures

(in reply to doogietim02)
       Post #: 15

Page:   [1]
All Forums >> RC Helicopters >> Exceed RC Support - Helicopter >> WK-G011 & TX
Page: [1]





Jump to:


 
Google 



Search | Marketplace | Event Calendar | Local Clubs | Magazine | Product Ratings | New Products | Discussion Forums

Photo Gallery | Instructor Search | Field|Track|Marina Search

Advertisers | Hobby Vendor Resources | Rate Manufacturers | Sign In/Sign Up

SITE MAP!   : :   FORUM RULES

RC Universe is a service of Internet Brands, Inc. Copyright © 2001-2013.

Charities we support that also need your help
Yorkie Rescue | Humane Society | ASPCA | Crohn's-Colitis America


0.438RCU1