Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Tab Content
  • Art ARRO's Avatar
    Today, 04:01 PM
    Art ARRO replied to a thread Reaction 54 Jet Kit in RC Jets
    Johnny, Twelve oz of lead to simulate a fully fueled UAT is a bit much-should be about 4 oz max. Rebalance with a 4 oz weight for the UAT and you...
    3540 replies | 558505 view(s)
  • Art ARRO's Avatar
    Today, 03:49 PM
    Art ARRO replied to a thread Reaction 54 Jet Kit in RC Jets
    Woketman, It is hard to attach the 4mm fuel line (from the pump to the turbine) to the 6mm Festo filter. Agree with using a 6 mm Festo upstream of...
    3540 replies | 558505 view(s)
  • Art ARRO's Avatar
    Today, 07:10 AM
    Art ARRO replied to a thread Reaction 54 Jet Kit in RC Jets
    Johnny, Sounds like a plan- good luck with the maiden and waiver qual. Rgds, Art ARRO
    3540 replies | 558505 view(s)
  • Art ARRO's Avatar
    Yesterday, 06:11 PM
    Art ARRO replied to a thread Reaction 54 Jet Kit in RC Jets
    Johnny, Like Mark said, get the JetCat filter vertical or near-vertical. You can relocate it closer to the turbine for this. Also safety wire all...
    3540 replies | 558505 view(s)
  • Art ARRO's Avatar
    05-22-2016, 01:25 PM
    Art ARRO replied to a thread Reaction 54 Jet Kit in RC Jets
    Johnny, Good explanation and glad you figured it out. These are the little details that can frustrate you on your initial setup. Another method...
    3540 replies | 558505 view(s)
  • Art ARRO's Avatar
    05-22-2016, 06:51 AM
    Johnny, I drilled down into this PST Sub-forum and noted that they offer fuel solenoid upgrade for their turbines with a TEMS ECU. This entails...
    5 replies | 103 view(s)
  • Art ARRO's Avatar
    05-21-2016, 08:35 AM
    Art ARRO replied to a thread Reaction 54 Jet Kit in RC Jets
    Woketman, As stated earlier, I used the Festo 4 mm filter without any problems until I saw a couple with split seams that leaked fuel into the jet. ...
    3540 replies | 558505 view(s)
  • Art ARRO's Avatar
    05-21-2016, 08:26 AM
    Johnny, I guess if the PST Manual only shows a gas solenoid I would go with that setup. As stated before switches are rarely used on the ECU...
    5 replies | 103 view(s)
  • Art ARRO's Avatar
    05-20-2016, 05:06 PM
    Johnny, Do you have the PST Operation Manual? There should be a installation diagram showing the turbine installation including all components and...
    5 replies | 103 view(s)
  • Art ARRO's Avatar
    05-20-2016, 10:54 AM
    Art ARRO replied to a thread Reaction 54 Jet Kit in RC Jets
    Johnny, On the Jet Cat filter you should hand tighten it initially then let it set overnight or so. On the second tightening you'll note that it...
    3540 replies | 558505 view(s)
  • Art ARRO's Avatar
    05-20-2016, 01:21 AM
    Art ARRO replied to a thread Reaction 54 Jet Kit in RC Jets
    Johnny, You can use one filter, preferably a Hangar 9 or Jet Cat, between the pump and the turbine. I've used the Festo 4 mm myself but was warned...
    3540 replies | 558505 view(s)
  • Art ARRO's Avatar
    05-19-2016, 03:25 PM
    Art ARRO replied to a thread Reaction 54 Jet Kit in RC Jets
    Johnny, You may want to exchange the Festo filter as these are prone to leak. If on the suction side of the fuel pump then air bubbles may be...
    3540 replies | 558505 view(s)
  • Art ARRO's Avatar
    05-11-2016, 06:12 PM
    Art ARRO replied to a thread Reaction 54 Jet Kit in RC Jets
    Les, Note that the engines has to cool down to less than 100 C before a reliable restart. The 18" fuel feed should not be a problem IF this segment...
    3540 replies | 558505 view(s)
  • Art ARRO's Avatar
    05-10-2016, 06:55 AM
    Johnny, You may want to hop over the the RC Pattern Forum for additional info on painting models. Pat Harris, (AKA Portlandflyer) is a superb...
    43 replies | 1712 view(s)
  • Art ARRO's Avatar
    05-09-2016, 04:52 PM
    Hi Kerry, I also have one of the first JR X9303 transmitters (purchased many years ago) which exhibited similar symptoms as yours. I shipped it...
    10 replies | 507 view(s)
No More Results
About Art ARRO

Basic Information

About Art ARRO
Location:
Holland Patent, NY

Statistics


Total Posts
Total Posts
570
Posts Per Day
0.35
General Information
Last Activity
Today 04:01 PM
Join Date
12-13-2011
Referrals
0
RCU Reviews
All times are GMT -6. The time now is 04:17 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.