Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Tab Content
  • kenh3497's Avatar
    04-29-2016, 08:16 AM
    True, but that is what testing get is for. The OP has weighed the risk factors and is happy with the balance considering where he flys. Ken
    9 replies | 389 view(s)
  • kenh3497's Avatar
    04-28-2016, 08:18 PM
    I don't see anything wrong with the repair. IMO a long as the cells were not damaged you should be good to go. Your repairs are nothing more than...
    9 replies | 389 view(s)
  • kenh3497's Avatar
    04-20-2016, 07:40 PM
    kenh3497 replied to a thread Ys 91fz in YS Engines Support
    I just had a simular issue with my newly rebuilt 91. I wound up taking the regulator apart and cleaned it a second time. Now it runs OK. 15% Sig...
    7 replies | 360 view(s)
  • kenh3497's Avatar
    04-18-2016, 06:33 PM
    I've always wrapped my RX's in foam. To date haven't had an issue with heat or vibration. Ken
    9 replies | 426 view(s)
  • kenh3497's Avatar
    04-18-2016, 06:31 PM
    You are correct. I need to read and UNDERSTAND what I am reading. Still the description is not clear and IMO leaves much to interpretation. Ken
    10 replies | 856 view(s)
  • kenh3497's Avatar
    04-14-2016, 08:51 PM
    The few barrel rolls I've done in the past I've applied up elevator and aileron at the same time. Controlling the amount of input will vary the...
    10 replies | 856 view(s)
  • kenh3497's Avatar
    04-12-2016, 06:56 PM
    I was always under the assumption a barrel roll was a positive G maneuver. Aileron and elevator applied at the same time to complete the maneuver. ...
    10 replies | 856 view(s)
  • kenh3497's Avatar
    04-10-2016, 07:49 PM
    I've had success with the acrylic paint from Hobby Lobby (craft store) then clear with automotive urethane. The urethane is 100%, well at least 99%...
    10 replies | 461 view(s)
  • kenh3497's Avatar
    04-10-2016, 07:45 AM
    Or just fill in the holes with 1/16 balsa and glass over. Many ways to skin the cat. I prefer to glass the fuse also if possible. I'm glad the...
    10 replies | 461 view(s)
  • kenh3497's Avatar
    04-09-2016, 09:35 PM
    I don't usually pay much attention to new engines but looking for some info on the YS site I see they have a "new" 80 4C available now. It seems YS...
    1 replies | 160 view(s)
  • kenh3497's Avatar
    04-03-2016, 05:13 PM
    Better photos Found something here. http://www.rcuniverse.com/forum/kit-building-121/11614120-xcelerator-xl-2-build.html And a bit on RC...
    4 replies | 513 view(s)
  • kenh3497's Avatar
    04-03-2016, 09:22 AM
    Here's a photo
    4 replies | 513 view(s)
  • kenh3497's Avatar
    04-03-2016, 06:29 AM
    Ya I should have taken a photo yesterday at the show. The show continues today so I'll take one and post it later this morning. I bought it mostly...
    4 replies | 513 view(s)
No More Results

Statistics


Total Posts
Total Posts
2,343
Posts Per Day
0.69
General Information
Join Date
01-21-2007
Referrals
0
RCU Reviews
All times are GMT -6. The time now is 07:15 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.