Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Tab Content
  • k_sonn's Avatar
    05-24-2016, 12:00 PM
    Newton, Here are the photos. In all of the photos, the engine is pushed as far forward as it can go and the cylinders are touching the sides of...
    134 replies | 10826 view(s)
  • k_sonn's Avatar
    05-23-2016, 04:49 PM
    The 84R3 won't fit in the cowl. I have an 84R3 in the box so tomorrow I'll take some photos for you. Kirk
    134 replies | 10826 view(s)
  • k_sonn's Avatar
    05-18-2016, 02:31 PM
    k_sonn replied to a thread skymaster pc-21 in RC Jets
    Nice flight Sergey. Congrats on the build and flight. Kirk
    253 replies | 25614 view(s)
  • k_sonn's Avatar
    05-18-2016, 02:09 PM
    k_sonn replied to a thread skymaster pc-21 in RC Jets
    Last year Kingtech USA was recommending not to use that prop. Contact Barry for more info. Last flying season I used a Solo Prop 3 bladed 22x22...
    253 replies | 25614 view(s)
  • k_sonn's Avatar
    05-09-2016, 12:19 PM
    k_sonn replied to a thread Kingtech Turbo Prop Engine in RC Jets
    I still had half a tank of fuel after belly landing. At some point during the flight the gray mpx plug had disconnected from the turbine. That plug...
    142 replies | 13008 view(s)
  • k_sonn's Avatar
    05-09-2016, 11:21 AM
    k_sonn replied to a thread Kingtech Turbo Prop Engine in RC Jets
    Here's some video of the Biela 5 blade 23x14 prop. After putting the gear down and backing off on the throttle I noticed the rpms had not...
    142 replies | 13008 view(s)
  • k_sonn's Avatar
    05-06-2016, 04:31 PM
    k_sonn replied to a thread Kingtech Turbo Prop Engine in RC Jets
    I ran the Beila 23x14 5 bladder and saw 5600 rpms on the ground and it was pulling pretty hard. When I fly it I'll try and video. Kirk
    142 replies | 13008 view(s)
  • Greg Wright's Avatar
    05-05-2016, 07:34 AM
    If it's a dark yellow to almost brown color then it is more than likely an Epoxy resin. If it's green in color then it is more than likely...
    12 replies | 587 view(s)
  • Greg Wright's Avatar
    05-05-2016, 07:30 AM
    Polyester will have a very strong almost sweet smell to it. A picture of the fuse would help to try and give you a clue.
    12 replies | 587 view(s)
  • Greg Wright's Avatar
    05-04-2016, 09:28 PM
    Sand the inside of the fuse were you want to glue something and you can tell by the smell if it's polyester resin or an epoxy resin. As far as...
    12 replies | 587 view(s)
  • Greg Wright's Avatar
    04-30-2016, 11:52 AM
    Vernon, This is just Awesome news to here!!! It couldn't happen if it wasn't for You and Michelle and her crew that allow us the Pilots to come...
    153 replies | 9846 view(s)
  • Greg Wright's Avatar
    04-29-2016, 05:47 PM
    Greg Wright replied to a thread JR8911HV issue in RC Jets
    Wow that must have been a pretty hard jolt to the servo to strip out an Aluminum arm. Are those what came on the servos when you bought them?
    17 replies | 913 view(s)
  • Greg Wright's Avatar
    04-29-2016, 07:00 AM
    Greg Wright replied to a thread JR8911HV issue in RC Jets
    So now i would use Aluminum Servo arms.
    17 replies | 913 view(s)
  • Greg Wright's Avatar
    04-27-2016, 06:19 PM
    Greg Wright replied to a thread JR8911HV issue in RC Jets
    Send them into HH with a good explanation of what is happening. I'm pretty sure they will take good care of you and replace them with new ones.
    17 replies | 913 view(s)
  • Greg Wright's Avatar
    04-27-2016, 01:57 PM
    Dave and Roger, Just to let you know. When i build my Huns i used 8911HV's thru out the whole plane on all of the main control surfaces with out...
    96 replies | 6602 view(s)
  • Greg Wright's Avatar
    04-26-2016, 06:06 AM
    Hi Melvin, If you think doing flite-metal to one is hard try building and doing it to two of them.. Lol!!! The Camo one was flite-metaled and then...
    96 replies | 6602 view(s)
No More Results
About BBMEX

Basic Information

About BBMEX
Location:
XALAPAVERACRUZ, MEXICO

Statistics


Total Posts
Total Posts
32
Posts Per Day
0.01
General Information
Last Activity
05-14-2016 08:52 AM
Join Date
02-13-2006
Referrals
0
RCU Reviews
All times are GMT -6. The time now is 06:01 AM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.