Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Tab Content
  • ETpilot's Avatar
    Yesterday, 11:28 AM
    ETpilot replied to a thread Grass Runway in Questions and Answers
    I debated width and length for a good while. Now that the pasture is clear I will go with this size n maybe downgrade when I get some flying...
    79 replies | 1768 view(s)
  • ETpilot's Avatar
    Yesterday, 06:06 AM
    ETpilot replied to a thread Grass Runway in Questions and Answers
    Yes, hunting season is about to start here. I hear practice gunfire in the distance. I have a lot of deer on my place but I do not hunt. A sanctuary...
    79 replies | 1768 view(s)
  • ETpilot's Avatar
    Yesterday, 05:47 AM
    ETpilot replied to a thread Throttle Return Spring in Gas Engines
    After speaking to the tech rep, I am going to be in the " leave the spring in place camp". I am using a good servo so I will see how that goes....
    34 replies | 1087 view(s)
  • ETpilot's Avatar
    10-18-2014, 11:51 AM
    ETpilot replied to a thread Grass Runway in Questions and Answers
    Well, I said I would post a picture. Here are a couple. I chose this site as it is close to the house and shop. I have better areas but this is the...
    79 replies | 1768 view(s)
  • ETpilot's Avatar
    10-12-2014, 05:57 PM
    ETpilot replied to a thread Throttle Return Spring in Gas Engines
    In all my readings, I read to disconnect. This is the first time I read to leave it connected. So I posed the question. Since the engine is in...
    34 replies | 1087 view(s)
  • ETpilot's Avatar
    10-12-2014, 07:41 AM
    I am a gas newbie and I am at the point in my build where I will be rigging my engine. I reviewed the Sticky " Newbie to Gas General Information " ...
    34 replies | 1087 view(s)
  • ETpilot's Avatar
    10-09-2014, 05:34 PM
    Thanks for the info. After I make the tailwheel assembly I will install the engine and make a wooden support for the LG assembly. I'm trying to stay...
    5 replies | 163 view(s)
  • ETpilot's Avatar
    10-09-2014, 05:46 AM
    I am building my first gas engine plane. It will be a tail dragger and I am at the point of making the LG assembly. This will be a grass runway flyer...
    5 replies | 163 view(s)
  • ETpilot's Avatar
    09-24-2014, 03:46 AM
    That installation is looking good. Thanks for that link. I'm going to see if I can get by with the 3/32 gear wire. I can then use the 3/32 bracket in...
    10 replies | 174 view(s)
  • ETpilot's Avatar
    09-23-2014, 06:36 PM
    HS = Hobbistar. I should have written it out. My bad. That second mod looks good. I was thinking of making something like that for my tailwheel. At...
    10 replies | 174 view(s)
  • ETpilot's Avatar
    09-22-2014, 05:48 AM
    That looks like a good mod you are doing. I am building a 60 size Ugly Stik taildragger and trying to decide on wheel size and how to mount it. This...
    10 replies | 174 view(s)
  • ETpilot's Avatar
    09-22-2014, 05:31 AM
    ETpilot replied to a thread Grass Runway in Questions and Answers
    Interesting problem. I don't think I have a lost plane problem unless it's lost in the woods. I'm too new to RC to be of help. I'm just learning...
    79 replies | 1768 view(s)
  • ETpilot's Avatar
    09-21-2014, 05:53 AM
    ETpilot replied to a thread Grass Runway in Questions and Answers
    Yes, I was thinking crash. Lost is another problem.
    79 replies | 1768 view(s)
No More Results
About ETpilot

Basic Information

About ETpilot
Location:
East Texas

Statistics


Total Posts
Total Posts
64
Posts Per Day
0.48
General Information
Last Activity
Today 05:23 AM
Join Date
06-09-2014
Referrals
0
All times are GMT -6. The time now is 12:52 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.