Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Tab Content
  • flybyjohn's Avatar
    Yesterday, 03:49 PM
    flybyjohn replied to a thread Mousse can logic? in Glow Engines
    I am thinking about using this engine combination on a Ultra sport 60. I kind of want as fast as I can go with the ability to still have enough...
    14 replies | 230 view(s)
  • flybyjohn's Avatar
    Yesterday, 03:47 PM
    flybyjohn replied to a thread Mousse can logic? in Glow Engines
    I made up a new can with a little longer pipe attached. I used a 12/9 apc prop and cut 1/2 inch at a time( should have stuck with 1/4"). 1st cut got...
    14 replies | 230 view(s)
  • flybyjohn's Avatar
    02-17-2017, 11:57 AM
    flybyjohn replied to a thread Mousse can logic? in Glow Engines
    So would it be a good assumption then if the a stub of pipe is already welded to the inlet of the can, that I would start cutting the header shorter,...
    14 replies | 230 view(s)
  • flybyjohn's Avatar
    02-17-2017, 10:19 AM
    flybyjohn replied to a thread Mousse can logic? in Glow Engines
    Does the length you are referring to mean the length from the end of the pipe to the back of the can or the length from the exhaust port to the back...
    14 replies | 230 view(s)
  • flybyjohn's Avatar
    02-17-2017, 09:18 AM
    flybyjohn replied to a thread Mousse can logic? in Glow Engines
    the long skinny can is about 10 inches long and the short fat is about 7.5 inches long, the inside capacity of each can is almost the same measured...
    14 replies | 230 view(s)
  • flybyjohn's Avatar
    02-17-2017, 08:21 AM
    I recently bought a tower hobbies .75 engine that needed agood cleaning but was still relatively tight at the top end. It did not have a muffler and...
    14 replies | 230 view(s)
  • flybyjohn's Avatar
    02-02-2017, 07:33 AM
    I used Balsawoodinc.com for my last scratch build. Most of the wood was good, only a sheet or two of the 1/16" got wavy on me. The price was the...
    6 replies | 289 view(s)
  • flybyjohn's Avatar
    01-31-2017, 09:09 AM
    flybyjohn replied to a thread Kwik Cote? in Kit Building
    Thanks yankee. It feels pretty stretchy, kind of a rubbery feel.
    4 replies | 177 view(s)
  • flybyjohn's Avatar
    01-30-2017, 08:19 PM
    flybyjohn replied to a thread Kwik Cote? in Kit Building
    Well it must be older then the oldest modelers here. I will give it a test on some scraps and see just how it behaves.
    4 replies | 177 view(s)
  • flybyjohn's Avatar
    01-26-2017, 09:47 AM
    flybyjohn started a thread Kwik Cote? in Kit Building
    I am getting ready to finish my ultra sport 60 and came across two rolls of this (Kwik Cote) in an old box of covering from an old modeler. I was...
    4 replies | 177 view(s)
No More Results
About flybyjohn

Basic Information

About flybyjohn
Location:
Helena, MT

Statistics


Total Posts
Total Posts
626
Posts Per Day
0.13
General Information
Last Activity
Today 08:00 AM
Join Date
01-14-2004
Referrals
0
RCU Reviews
All times are GMT -8. The time now is 11:31 AM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.