Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

  • Hobbsy's Avatar
    01-04-2017, 07:48 AM
    Hobbsy replied to a thread Welcome to Club SAITO ! in Glow Engines
    Typical setting.
    32971 replies | 1989145 view(s)
  • Hobbsy's Avatar
    01-04-2017, 05:40 AM
    Hobbsy replied to a thread Welcome to Club SAITO ! in Glow Engines
    Two items on this page will fix you up, the idle needle, (actually a sleeve that slides in and out over the spray bar), and the spray bar itself. ...
    32971 replies | 1989145 view(s)
  • Hobbsy's Avatar
    01-03-2017, 11:27 AM
    Hobbsy replied to a thread Welcome to Club SAITO ! in Glow Engines
    From my observations the flow is stop and go until about 4,000 rpm and then it is steadily outward. I don't think there is enough "in" to worry...
    32971 replies | 1989145 view(s)
  • Hobbsy's Avatar
    01-03-2017, 09:05 AM
    Hobbsy replied to a thread Loose Wrist Pin repair. Webra 25 in Glow Engines
    Here is my .40 piston, it is not wallowed out in the horizontal direction, only the vertical. I don't have the correct K&S tubing. I'll get it.
    11 replies | 272 view(s)
  • Hobbsy's Avatar
    01-02-2017, 10:07 AM
    Hobbsy replied to a thread Welcome to Club SAITO ! in Glow Engines
    This puts the vent juice in the exhaust stream, I doubt that enough venturi effect happens to aid anything. In a larger diameter tube the by pass oil...
    32971 replies | 1989145 view(s)
  • Hobbsy's Avatar
    01-02-2017, 04:42 AM
    Hobbsy replied to a thread Loose Wrist Pin repair. Webra 25 in Glow Engines
    I have A Webra SilverLine .40 in the same condition, the wrist pin bores are worn oblong because the pin bore in the rod is too tight and the wrist...
    11 replies | 272 view(s)
  • Hobbsy's Avatar
    12-31-2016, 09:48 AM
    Hobbsy replied to a thread Welcome to Club SAITO ! in Glow Engines
    It has .66 cubic inch by way of an increase in the bore from 1.03" to 1.06", the stroke is .75".
    32971 replies | 1989145 view(s)
  • Hobbsy's Avatar
    12-31-2016, 04:01 AM
    Hobbsy replied to a thread Welcome to Club SAITO ! in Glow Engines
    That 50 to 1 mixture is for engines like Stihl engines that have all needle bearings on the crank and rod.. PS, the FG 11 is slightly larger at...
    32971 replies | 1989145 view(s)
  • Hobbsy's Avatar
    12-30-2016, 09:05 AM
    Hobbsy replied to a thread Welcome to Club SAITO ! in Glow Engines
    That's when Horizon says they're coming, money wise, the timing is better. Most know how that is at times.
    32971 replies | 1989145 view(s)
  • Hobbsy's Avatar
    12-30-2016, 04:08 AM
    Hobbsy replied to a thread Welcome to Club SAITO ! in Glow Engines
    Hey there Pete, yep, the Misterbishi made the 400 mile trip using one half quart of oil going and another half quart on the return. My brother in...
    32971 replies | 1989145 view(s)
  • Hobbsy's Avatar
    12-29-2016, 07:57 PM
    The engine has a bronze bushing instead of ball bearings, all other things being equal they will have the same power. After all a turbo charger shaft...
    321 replies | 6516 view(s)
  • Hobbsy's Avatar
    12-29-2016, 12:57 PM
    Hobbsy replied to a thread Welcome to Club SAITO ! in Glow Engines
    Make sure the throttle is not fully closed when checking the compression, that has fooled many a man. Saitos have very good compression, even when...
    32971 replies | 1989145 view(s)
  • Hobbsy's Avatar
    12-29-2016, 08:10 AM
    Hobbsy replied to a thread Enya 80 4C hard to prime in Glow Engines
    Yep,there are a lot of successful recipes. I remove the chokes from all engines except the Enya's that have the barrel sliding sideways choke.
    18 replies | 351 view(s)
  • Hobbsy's Avatar
    12-29-2016, 05:56 AM
    Hobbsy replied to a thread Enya 80 4C hard to prime in Glow Engines
    When using a starter there is no need to prime and it will pull fuel to the carb at idle even with an air bleed carb. Any Enya that i owned over the...
    18 replies | 351 view(s)
  • Hobbsy's Avatar
    12-22-2016, 04:07 AM
    Hobbsy replied to a thread Welcome to Club SAITO ! in Glow Engines
    Good AM to you Pete, I may be a bad guy in January and get my self an FG 11. One crying out to me for a good home. Gonna drive 400 miles to my...
    32971 replies | 1989145 view(s)
  • Hobbsy's Avatar
    12-21-2016, 05:49 PM
    Hobbsy replied to a thread Os 1.20 in Glow Engines
    Propeller: 15x10-12 or 16x8-10 Field Equipment: Glow starter, fuel filter, fuel pump, fuel tubing
    10 replies | 283 view(s)
  • Hobbsy's Avatar
    12-21-2016, 05:41 PM
    Hobbsy replied to a thread Welcome to Club SAITO ! in Glow Engines
    This is possibly the first Saito 1.50 sold, at least according to a lady at Horizon. It is a 1.50S and now the 1.50's are in the new case and are...
    32971 replies | 1989145 view(s)
  • Hobbsy's Avatar
    12-21-2016, 05:33 PM
    Hobbsy replied to a thread OS FS-95V four-stroke. Why so cheap? in Glow Engines
    True enough, think that my only Saito with a bushed rod is my old high compression .80.
    6 replies | 251 view(s)
  • Hobbsy's Avatar
    12-21-2016, 02:03 PM
    Hobbsy replied to a thread Welcome to Club SAITO ! in Glow Engines
    The Saito .91's were all S models. They were the last of the mid block, .65, .80 and .91. The .91 was replaced with the 1.00 in the newer B block ...
    32971 replies | 1989145 view(s)
  • Hobbsy's Avatar
    12-21-2016, 06:41 AM
    You're trying to illicit responses from folks who are going to buy Saitos or OS or Enya's or LASER's regardless of whether lined or linerless. To...
    21 replies | 518 view(s)
  • Hobbsy's Avatar
    12-21-2016, 04:43 AM
    Based on my unbiased observations the Saito and OS are equal in quality with Saito having an edge in performance. Pictured is a 1992 Saito 1.50...
    21 replies | 518 view(s)
  • Hobbsy's Avatar
    12-21-2016, 04:04 AM
    Hobbsy replied to a thread OS FS-95V four-stroke. Why so cheap? in Glow Engines
    And that is not a bad thing.
    6 replies | 251 view(s)
  • Hobbsy's Avatar
    12-20-2016, 03:55 AM
    Hobbsy replied to a thread OS FS-95V four-stroke. Why so cheap? in Glow Engines
    I have one and it is a fine engine, I also have an OS .56 Alpha, it too is a fine engine. Here is a shot of the 95v running and of it's vent. The OS...
    6 replies | 251 view(s)
  • Hobbsy's Avatar
    12-20-2016, 03:40 AM
    I've been perusing and posting on these pages since this was called RCOnline more than 25 years ago. The only Saito I saw messed up was one that had...
    21 replies | 518 view(s)
  • Hobbsy's Avatar
    12-19-2016, 10:10 AM
    Hobbsy replied to a thread Club FOX! in Glow Engines
    https://www.bocabearings.com/products/enk-037-2046?make=FOX+ENGINES&model=QUICKIE&feature=45 These are for the Quicky 45 and cost 8 bucks more...
    4872 replies | 304818 view(s)
  • Hobbsy's Avatar
    12-18-2016, 08:48 PM
    Hobbsy replied to a thread *** CLUB SUPER TIGRE *** in Glow Engines
    There is a spring in side the high speed needle, I just take a push pin and pick the O-ring right out. All you do to install the new one is slide it...
    2096 replies | 153257 view(s)
  • Hobbsy's Avatar
    12-18-2016, 11:03 AM
    The LA's handle Diesel conversion very well, they'll handle anything you throw at them.
    321 replies | 6516 view(s)
  • Hobbsy's Avatar
    12-17-2016, 06:01 PM
    Hobbsy replied to a thread *** CLUB SUPER TIGRE *** in Glow Engines
    Both the LS needle and the HS needle have an O-ring on them, no fuel line needed.
    2096 replies | 153257 view(s)
  • Hobbsy's Avatar
    12-17-2016, 08:38 AM
    Hobbsy replied to a thread Club Laser? in Glow Engines
    Thanks, and yes I saw those also and questioned them as that didn't make sense.
    465 replies | 42754 view(s)
  • Hobbsy's Avatar
    12-17-2016, 05:43 AM
    Hobbsy replied to a thread Club Laser? in Glow Engines
    My .70 rode in this Kombat 60 from the Airplane Factory. The Airplane Factory was completely destroyed by Hurricane Katrina, The owner did not...
    465 replies | 42754 view(s)
More Activity
About gatorswinall1

Basic Information

About gatorswinall1
Location:
O-town, FL

Statistics


Total Posts
Total Posts
4
Posts Per Day
0.00
General Information
Join Date
02-01-2006
Referrals
0
RCU Reviews
All times are GMT -8. The time now is 07:30 AM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.