Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Tab Content
  • w8ye's Avatar
    Today, 09:40 AM
    w8ye replied to a thread which is better? in Gas Engines
    At my flying field everyone has at least one DA and no one has a Roto. There have been some problems with the DA's at times but the factory has...
    3 replies | 87 view(s)
  • w8ye's Avatar
    Today, 09:37 AM
    w8ye replied to a thread Frank Bowman Rings in Gas Engines
    He was not always Johnny on spot with his Emails in the past.
    4 replies | 80 view(s)
  • w8ye's Avatar
    Yesterday, 09:17 AM
    Av8tor - very good post
    8 replies | 101 view(s)
  • w8ye's Avatar
    11-20-2014, 01:39 PM
    If it is in more or less a blind pocket where you cannot get behind it, I heat the case up to 350 F or 180C and bang the hot case against a board to...
    8 replies | 101 view(s)
  • w8ye's Avatar
    11-19-2014, 07:47 PM
    w8ye replied to a thread Saito FG-20 or 21 in Gas Engines
    +1
    1751 replies | 192438 view(s)
  • w8ye's Avatar
    11-16-2014, 01:28 PM
    It may just have some trash stuck in it?
    12 replies | 187 view(s)
  • w8ye's Avatar
    11-15-2014, 09:30 AM
    The needle of the metering valve in the carb is not seating.
    12 replies | 187 view(s)
  • w8ye's Avatar
    11-11-2014, 02:23 PM
    w8ye replied to a thread Mintor 22 Piston in Gas Engines
    I always took it for granted that I would pass away long before my wife . . . She passed away 17 1/2 yrs ago. She was never in the hospital...
    81 replies | 2373 view(s)
  • w8ye's Avatar
    11-09-2014, 01:17 PM
    I have a complement of Kioritz/Echo yard implements. They are nothing but the best.
    6 replies | 314 view(s)
  • w8ye's Avatar
    11-09-2014, 09:46 AM
    w8ye replied to a thread Mintor 22 Piston in Gas Engines
    Richard, My thoughts are with you and the rest of the family. Jim
    81 replies | 2373 view(s)
  • w8ye's Avatar
    11-08-2014, 01:15 PM
    w8ye replied to a thread Converting to Gas in Gas Engines
    You can use two twin cyl ignitions. Mount the sensors 180 degrees apart One ignition fires 1,4 and the other 3,2 Timing is 28 degrees BTDC ...
    2 replies | 144 view(s)
  • w8ye's Avatar
    11-06-2014, 07:25 PM
    w8ye replied to a thread Saito 150B Gas carb in Gas Engines
    I have a 150 with CH ignition and I use the glow carb on gas.
    5 replies | 194 view(s)
  • w8ye's Avatar
    11-06-2014, 02:37 PM
    w8ye replied to a thread Saito 150B Gas carb in Gas Engines
    http://ch-ignitions.com/index.php
    5 replies | 194 view(s)
  • w8ye's Avatar
    11-06-2014, 02:35 PM
    w8ye replied to a thread Saito FG-21 Timing Pin? in Gas Engines
    It is not a common problem. The glow Saito125 does not have the pin but a brass tapered split sleeve.
    3 replies | 127 view(s)
  • w8ye's Avatar
    11-06-2014, 11:29 AM
    w8ye replied to a thread Saito FG-21 Timing Pin? in Gas Engines
    The prop driver hub on the FG20/FG21 is indexed or located by a threaded pin that impinges into a hole in the crankshaft. A back fire or prop...
    3 replies | 127 view(s)
  • w8ye's Avatar
    10-29-2014, 09:05 PM
    w8ye replied to a thread Primer bulb??? in Gas Engines
    +1 on the name brand conversions. I have some Stihl 27cc weed whacker engines and Stihl 025/MS250 chainsaw engines that have radial mount and beam...
    33 replies | 2239 view(s)
  • w8ye's Avatar
    10-28-2014, 12:18 PM
    w8ye replied to a thread Engine ID? in Gas Engines
    You are likely correct. My experience with other people's bigger CRRCPRO engines was not good at all. Next to the worthless category. The Ryobi...
    9 replies | 341 view(s)
  • w8ye's Avatar
    10-27-2014, 11:06 PM
    w8ye replied to a thread Engine ID? in Gas Engines
    They are conversion weed whackers Don't bring much money at swap meets Could be a reasonable experience if they're yours. You could enjoy them...
    9 replies | 341 view(s)
  • w8ye's Avatar
    10-27-2014, 08:20 PM
    w8ye replied to a thread Engine ID? in Gas Engines
    The top engine started life as a Ryobi 31 weed whacker with a stamped steel two piece and riveted together connecting rod and the counter weight and...
    9 replies | 341 view(s)
  • w8ye's Avatar
    10-27-2014, 12:23 PM
    w8ye replied to a thread Mintor 22 Piston in Gas Engines
    I've been using Caber rings. They are the most popular aftermarket ring for chainsaws and yard equipment. They are made in Italy. They are...
    81 replies | 2373 view(s)
  • w8ye's Avatar
    10-25-2014, 12:13 AM
    w8ye replied to a thread What is a BME50? in Gas Engines
    For the record http://www.ereplacementparts.com/echo-cs520-c09312001001-c09312999999-chainsaw-parts-c-35043_35970_36796.html
    6 replies | 252 view(s)
  • w8ye's Avatar
    10-23-2014, 12:48 PM
    w8ye replied to a thread gas cans in Gas Engines
    Match the O rings up at the hardware store
    33 replies | 1404 view(s)
  • w8ye's Avatar
    10-23-2014, 06:12 AM
    w8ye replied to a thread What is a BME50? in Gas Engines
    The parent company is Kioritz but in the USA they are ECHO. Shindaiwa is part of Kioritz or at least they merged one way or the other. It...
    6 replies | 252 view(s)
No More Results
About GrnBrt

Basic Information

Date of Birth
December 11, 1944 (69)
About GrnBrt
Location:
Everett, WA

Signature


Art Grabow SR
Senior forum Manager

US Army Special forces, mess with the best, die like the rest!

http://mysite.verizon.net/res0bf5n/houseofgrabow/index.html
http://mysite.verizon.net/res0bf5n/houseofgrabow/index.html

Statistics


Total Posts
Total Posts
6,988
Posts Per Day
1.48
General Information
Join Date
12-05-2001
Referrals
0
All times are GMT -6. The time now is 10:52 AM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.