Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

  • jonkoppisch's Avatar
    03-22-2017, 06:06 AM
    I always drooled at the rebel pro but it was a little out of my price range. The t3 just might scratch that itch. Will the t3 be at mississippi...
    1360 replies | 129320 view(s)
  • jonkoppisch's Avatar
    03-22-2017, 05:12 AM
    Is there a t3 thread yet? how does it compare in size and flying to the rebel pro? it looks like there's no comparison in price..
    1360 replies | 129320 view(s)
  • jonkoppisch's Avatar
    03-18-2017, 05:24 AM
    jonkoppisch replied to a thread Florida Jets Photos in RC Jets
    Friend posted this on facebook https://www.facebook.com/andy.woerner.5/posts/1470487322985109
    156 replies | 15585 view(s)
  • CraigG's Avatar
    03-11-2017, 12:18 PM
    CraigG replied to a thread Tomahawk Futura 2.5m in RC Jets
    Probably more accurate to call it the Y "inlet duct". "Pipe" generally refers to the other end....:) I think it's a great improvement. I would...
    65 replies | 10712 view(s)
  • CraigG's Avatar
    03-06-2017, 12:48 PM
    CraigG replied to a thread Paritech Natrix Build in RC Jets
    So far I like my Behotec e-retracts and brakes and I really like not having to fool with air pumps, air valves, air leaks, etc.. My Natrix was a...
    76 replies | 9105 view(s)
  • CraigG's Avatar
    03-06-2017, 08:17 AM
    CraigG replied to a thread Paritech Natrix Build in RC Jets
    Darin, Do you remember how much aileron deflection you have with your crow setup? Any pitch change with the crow? Thanks! Craig
    76 replies | 9105 view(s)
  • CraigG's Avatar
    03-05-2017, 03:38 AM
    CraigG replied to a thread Paritech Natrix Build in RC Jets
    Scott, Did you ever experiment crow on your Natrix? As you mentioned before, it is definitely a floater on landing. Thanks.....Craig
    76 replies | 9105 view(s)
  • CraigG's Avatar
    03-04-2017, 06:01 PM
    CraigG replied to a thread Paritech Natrix Build in RC Jets
    Finally maidened my Natrix today. Wow, what a really nice flying jet! Minimal trim with the CG at 380mm and super clean rolls. Mine came in at 40lbs...
    76 replies | 9105 view(s)
  • CraigG's Avatar
    03-03-2017, 05:56 AM
    CraigG replied to a thread Jeti-duplex-ds-16-2.4-ghz in RC Jets
    Good choice Jamie, you won't be disappointed. As others have mentioned, there's a learning curve but you will quickly realize the potential of this...
    3061 replies | 206506 view(s)
  • CraigG's Avatar
    02-25-2017, 04:05 PM
    CraigG replied to a thread Hysol 9462, Need Your Help in RC Jets
    Go with the Hysol. It's perfectly good for wood joints and it holds up better over the long run (years), particularly if the joint is exposed to...
    11 replies | 882 view(s)
  • CraigG's Avatar
    02-24-2017, 11:30 AM
    CraigG replied to a thread Fueling Can Suggestions in RC Jets
    Some of the guys like Mr. Funnel because it filters and separates out water. Its kind of a pain though because it leaves several ounces of fuel in...
    11 replies | 636 view(s)
  • jonkoppisch's Avatar
    02-24-2017, 09:30 AM
    Need a t2 ;)
    22 replies | 2251 view(s)
  • CraigG's Avatar
    02-23-2017, 04:21 PM
    CraigG replied to a thread AMT USA 280 Manual Needed in RC Jets
    Todd, I'l look and see if I can find one of my old AMT "manuals". I do recall that you have to "teach" the trim and throttle position on every...
    12 replies | 410 view(s)
No More Results
About jonkoppisch

Basic Information

About jonkoppisch
Location:
Mobile, AL

Signature


Announcing "I'm offended" is basically telling the world you can't control your own emotions, so everyone else should do it for you

Statistics


Total Posts
Total Posts
2,678
Posts Per Day
0.48
General Information
Last Activity
Today 04:03 AM
Join Date
12-17-2001
Referrals
0
RCU Reviews
All times are GMT -8. The time now is 05:36 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.