Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Tab Content
  • mlr53's Avatar
    Yesterday, 07:47 AM
    Who is planning to participate in the Georgetown clinic?
    6 replies | 245 view(s)
  • mlr53's Avatar
    02-14-2017, 08:50 AM
    mlr53 replied to a thread Allure Glow Build in RC Pattern Flying
    Thanks Jason, I found a lot of electric version build threads out there, but none for Glo.
    29 replies | 2326 view(s)
  • mlr53's Avatar
    02-13-2017, 12:36 PM
    mlr53 replied to a thread Allure Glow Build in RC Pattern Flying
    Set the motor with mount and nose ring in place and look atthe clearance between the beam plate and the motor. Pull the motor assembly outand trim...
    29 replies | 2326 view(s)
  • mlr53's Avatar
    02-13-2017, 12:35 PM
    mlr53 replied to a thread Allure Glow Build in RC Pattern Flying
    Next, trim and fit the fire wall plate to fit in place inthe fuse behind the beam plate. Be sure it keys into the beam plate asintended. It will fall...
    29 replies | 2326 view(s)
  • mlr53's Avatar
    02-13-2017, 12:31 PM
    mlr53 replied to a thread Allure Glow Build in RC Pattern Flying
    Assure the fuselage and motor are aligned straight andvertical in the opening, then ease in the beam plate into position. Check thefit, remove and...
    29 replies | 2326 view(s)
  • mlr53's Avatar
    02-13-2017, 12:30 PM
    mlr53 replied to a thread Allure Glow Build in RC Pattern Flying
    Then slid my motor assembly with nose ring and motor mountinto the plane with the prop shaft thru the jig plate and using a prop hub,washer and prop...
    29 replies | 2326 view(s)
  • mlr53's Avatar
    02-13-2017, 12:23 PM
    mlr53 replied to a thread Allure Glow Build in RC Pattern Flying
    I made a nose plate jig to help hold my motor in place withthe proper alignment when fitting the beam plate into the nose. It is the same OD as...
    29 replies | 2326 view(s)
  • mlr53's Avatar
    02-13-2017, 12:18 PM
    mlr53 replied to a thread Allure Glow Build in RC Pattern Flying
    Cuta strong back from 3/16” aircraft ply to add support to the motor mount andallow for the blind nuts to have meat to set in. This should be about 1...
    29 replies | 2326 view(s)
  • mlr53's Avatar
    02-13-2017, 12:15 PM
    mlr53 replied to a thread Allure Glow Build in RC Pattern Flying
    Cuttwo pieces of 3/16” aircraft ply to glue to the beam plate as doublers wherethe nose ring bolts will be to give some meat for the blind nuts to...
    29 replies | 2326 view(s)
  • mlr53's Avatar
    02-13-2017, 12:04 PM
    mlr53 replied to a thread Allure Glow Build in RC Pattern Flying
    Test fit the beam plate into the nose of the Allure, andtrim it to fit snugly in it’s approximate place. Note that the engine cut outis offset to...
    29 replies | 2326 view(s)
  • mlr53's Avatar
    02-13-2017, 12:00 PM
    mlr53 replied to a thread Allure Glow Build in RC Pattern Flying
    Since JetPilot didn't get around to covering the engine compartment, I figure I would post my build thread for mounting a YS 185 glo engine, in order...
    29 replies | 2326 view(s)
  • mlr53's Avatar
    02-13-2017, 10:38 AM
    Papaone, that picture was taken at the Cajun Nationals, and that is a picture of the Allure biplane. The designer Bryan Hebert has been testing his...
    15 replies | 1037 view(s)
No More Results
About mlr53

Basic Information

About mlr53
Location:
Scott, LA

Signature


Monte
AMA 5581 CD
NSRCA 4469
RAMS (Rice Area Modelers Society)
RAT Pack (Rams Aerobatic Team)

Statistics


Total Posts
Total Posts
176
Posts Per Day
0.08
General Information
Last Activity
Today 06:59 AM
Join Date
05-16-2011
Referrals
0
RCU Reviews
All times are GMT -8. The time now is 07:31 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.