Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

  • rctom's Avatar
    Yesterday, 08:38 AM
    I have a CF tube that will fit, contact me at wildharerc@gmail.com. We had a couple different CF gears, some were good and some not so much.
    1 replies | 33 view(s)
  • rctom's Avatar
    10-06-2014, 07:50 AM
    Sorry but there's no hope. I have nothing for that plane, and while I have a bunch of cowls for the later Extras and other planes they would be much...
    1 replies | 89 view(s)
  • BAS's Avatar
    09-30-2014, 05:33 PM
    BAS replied to a thread Sig 4-star new arfs in ARF or RTF
    Yep I agree on the tail feathers but I never go much over half throttle with the YS 115 I cant believe the torque this motor has I think it would...
    17 replies | 492 view(s)
  • BAS's Avatar
    09-29-2014, 08:11 AM
    BAS replied to a thread Ys 115fz s in YS Engines Support
    Ok thanks for the info
    11 replies | 195 view(s)
  • BAS's Avatar
    09-29-2014, 04:10 AM
    BAS replied to a thread Sig 4-star new arfs in ARF or RTF
    I flew my four star today and just had the used low rudder rate for the 1st take off and had no bad habits or yaw at all. Of course with the YS 115...
    17 replies | 492 view(s)
  • BAS's Avatar
    09-29-2014, 04:06 AM
    BAS replied to a thread Ys 115fz s in YS Engines Support
    Ok finally got to fly my 4-star 64 with the YS 115. Turning a APC 17/4 wide blade and it is a perfect combo. This motor has got some grunt I ran 2...
    11 replies | 195 view(s)
  • BAS's Avatar
    09-27-2014, 12:37 PM
    BAS replied to a thread Sig 4-star new arfs in ARF or RTF
    The spruce strengthen the wire and keeps it from flexing under stress conditions I agree on what yu said about quality control but over all its not...
    17 replies | 492 view(s)
  • BAS's Avatar
    09-27-2014, 03:56 AM
    BAS replied to a thread Sig 4-star new arfs in ARF or RTF
    Just wondering I need to find out if anyone has moved the rearward cg of 4 and 3/8 further back and still had a stable flying plane. With the big YS...
    17 replies | 492 view(s)
  • BAS's Avatar
    09-26-2014, 07:58 PM
    BAS replied to a thread Ys 115fz s in YS Engines Support
    Ok thanks for the good info on the motor I take it your running full throttle using the 14 ozs of fuel in 4 minutes? I will be running under half...
    11 replies | 195 view(s)
  • BAS's Avatar
    09-26-2014, 02:16 AM
    BAS replied to a thread Sig 4-star new arfs in ARF or RTF
    Per Mikes and Bobs advice I put a small 1/4 square piece of spruce on the rear side of the elevator joiner the part that is exposed gluing it with...
    17 replies | 492 view(s)
  • BAS's Avatar
    09-24-2014, 03:49 PM
    BAS replied to a thread Ys 115fz s in YS Engines Support
    I appreciate your reply but I am not into speed at all I want my planes to fly slow with a lot of low end torque for hovering and 3d I run my 140 ys...
    11 replies | 195 view(s)
No More Results
About Tired Old Man

Basic Information

About Tired Old Man
Location:
Valley Springs, CA

Signature


Never lie, and never minimize or gloss. Tell it like it is and let the pieces fall where they may. The truth always wins.

Statistics


Total Posts
Total Posts
18,602
Posts Per Day
4.02
General Information
Last Activity
07-08-2014 06:00 PM
Join Date
02-25-2002
Referrals
0
All times are GMT -6. The time now is 06:42 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.