KK board questions
#1
Member
Thread Starter
Join Date: Feb 2006
Location: Wappingers Falls,
NY
Posts: 30
Likes: 0
Received 0 Likes
on
0 Posts
KK board questions
So I got the KK black board version 5.5 (Atmega 168PA). I think firmware version 2.5 (x) is loaded and I also have the USBasp programmer. I have a few questions since I'm not familiar with this board.
1. Is there a way to tell what firmware is loaded on the board using the programmer?
2. What flash tool is recommended? I have kkmulticopter flashtool v0.62 and AVR Studio 4. AVR is giving error when trying to select programmer. The other flash tool loads.
3. Can the board get damaged if you set the wrong settings upon flashing?
4. Is there a difference in firmware between blue and black?
5. Can you flash blue fw to a black board?
Thanks
1. Is there a way to tell what firmware is loaded on the board using the programmer?
2. What flash tool is recommended? I have kkmulticopter flashtool v0.62 and AVR Studio 4. AVR is giving error when trying to select programmer. The other flash tool loads.
3. Can the board get damaged if you set the wrong settings upon flashing?
4. Is there a difference in firmware between blue and black?
5. Can you flash blue fw to a black board?
Thanks
#2
Senior Member
My Feedback: (11)
Join Date: Aug 2004
Location: saint joseph,
MO
Posts: 1,253
Likes: 0
Received 0 Likes
on
0 Posts
RE: KK board questions
ORIGINAL: jmc67
So I got the KK black board version 5.5 (Atmega 168PA). I think firmware version 2.5 (x) is loaded and I also have the USBasp programmer. I have a few questions since I'm not familiar with this board.
1. Is there a way to tell what firmware is loaded on the board using the programmer?
2. What flash tool is recommended? I have kkmulticopter flashtool v0.62 and AVR Studio 4. AVR is giving error when trying to select programmer. The other flash tool loads.
3. Can the board get damaged if you set the wrong settings upon flashing?
4. Is there a difference in firmware between blue and black?
5. Can you flash blue fw to a black board?
Thanks
So I got the KK black board version 5.5 (Atmega 168PA). I think firmware version 2.5 (x) is loaded and I also have the USBasp programmer. I have a few questions since I'm not familiar with this board.
1. Is there a way to tell what firmware is loaded on the board using the programmer?
2. What flash tool is recommended? I have kkmulticopter flashtool v0.62 and AVR Studio 4. AVR is giving error when trying to select programmer. The other flash tool loads.
3. Can the board get damaged if you set the wrong settings upon flashing?
4. Is there a difference in firmware between blue and black?
5. Can you flash blue fw to a black board?
Thanks
2. I use the Lazy Zero flashtool. It's probably the easiest one out there.
3. The board can't really be damaged by the firmware. If you don't like the firmware, simply load another and it will be fine.
4. Doesn't matter what the color is. They are all KK boards.
5. Any firmware that works on any kk board will work on any other.
[youtube]http://www.youtube.com/watch?v=NmT73uHj5nw[/youtube]
#5
Member
Thread Starter
Join Date: Feb 2006
Location: Wappingers Falls,
NY
Posts: 30
Likes: 0
Received 0 Likes
on
0 Posts
RE: KK board questions
Ok, I loaded fw 4.7 from a hex file (taken from rcgroups) with no issues but there was no way to tell if it is acro. Everything is setup in terms of motors/props. I bench tested to make sure the tx and gyro response is correct. Does anyone know if this firmware supports changing flight mode with the tx?
What are the differences between the different modes?
Thanks
What are the differences between the different modes?
Thanks
#6
Senior Member
My Feedback: (11)
Join Date: Aug 2004
Location: saint joseph,
MO
Posts: 1,253
Likes: 0
Received 0 Likes
on
0 Posts
RE: KK board questions
You can't change the flight mode from the TX and I have only flown X4.7 and +4.7 so I'm not well versed in the other areas. I know that Lazy Zero has an "acro" mode in the firmware but haven't tried it yet either.
#7
Member
Thread Starter
Join Date: Feb 2006
Location: Wappingers Falls,
NY
Posts: 30
Likes: 0
Received 0 Likes
on
0 Posts
RE: KK board questions
I got it all setup and running good, thanks. Does anyone know if the FMA co-pilot II can be installed and used with the KK board?
#8
Senior Member
My Feedback: (11)
Join Date: Aug 2004
Location: saint joseph,
MO
Posts: 1,253
Likes: 0
Received 0 Likes
on
0 Posts
RE: KK board questions
I don't think FMA works with it. Hobbyking is coming out with a KK board with accelerometers for only 30 dollars so a copilot won't even be necessary.
http://www.hobbyking.com/hobbyking/s...rol_Board.html
http://www.hobbyking.com/hobbyking/s...rol_Board.html
#9
Member
Thread Starter
Join Date: Feb 2006
Location: Wappingers Falls,
NY
Posts: 30
Likes: 0
Received 0 Likes
on
0 Posts
RE: KK board questions
I think you are referring to the KK2. I have one on order.
ORIGINAL: randall1959
I don't think FMA works with it. Hobbyking is coming out with a KK board with accelerometers for only 30 dollars so a copilot won't even be necessary.
http://www.hobbyking.com/hobbyking/s...rol_Board.html
I don't think FMA works with it. Hobbyking is coming out with a KK board with accelerometers for only 30 dollars so a copilot won't even be necessary.
http://www.hobbyking.com/hobbyking/s...rol_Board.html