RC Surfer
#7576
Join Date: May 2009
Location: Cape Towm, SOUTH AFRICA
Posts: 2,769
Likes: 0
Received 0 Likes
on
0 Posts
New YPC Board Design 2014
Something new for 2014.....a new build with a few 'small tweaks'..pun intended..
Follow the build at this link address: http://www.rcuniverse.com/forum/rc-b...l#post11768555
Follow the build at this link address: http://www.rcuniverse.com/forum/rc-b...l#post11768555
#7577
Member
Join Date: Feb 2011
Location: Calgary, AB, CANADA
Posts: 45
Likes: 0
Received 0 Likes
on
0 Posts
Finally BoardShark time
Bear,
It wont stop dumping SNOW here, its a ridiculous winter. I am ready for some summer, it would be great if the snow stays in the Mountains.
I got around to working on this Shark...Yay
I cut up a few plates of metal, and I also cut a big ugly hole in the deck of the board.
https://www.youtube.com/watch?v=aAGjh5D0OVY&list=HL1395842385&feature=mh_lolz
It wont stop dumping SNOW here, its a ridiculous winter. I am ready for some summer, it would be great if the snow stays in the Mountains.
I got around to working on this Shark...Yay
I cut up a few plates of metal, and I also cut a big ugly hole in the deck of the board.
https://www.youtube.com/watch?v=aAGjh5D0OVY&list=HL1395842385&feature=mh_lolz
Last edited by ronkytonk; 03-26-2014 at 06:33 AM.
#7578
Senior Member
Join Date: Jul 2011
Location: Haiku, HI
Posts: 141
Likes: 0
Received 0 Likes
on
0 Posts
Ronk- Looking Good !! If you run into any clearance problems you should be able to flip both servo arms and run the pushrod on the rail side.
You also want the arms to be parallel, and the pushrod to be at 90 degrees to the arm in the center position.
You also want the arms to be parallel, and the pushrod to be at 90 degrees to the arm in the center position.
Last edited by K-H2o; 03-26-2014 at 12:54 PM.
#7579
Join Date: May 2009
Location: Cape Towm, SOUTH AFRICA
Posts: 2,769
Likes: 0
Received 0 Likes
on
0 Posts
Build Progress: http://www.rcuniverse.com/forum/rc-b...l#post11769535 link for more details of process.
Last edited by YPC; 03-27-2014 at 02:54 AM.
#7580
Join Date: May 2009
Location: Cape Towm, SOUTH AFRICA
Posts: 2,769
Likes: 0
Received 0 Likes
on
0 Posts
The past few days of rain have dissipated and another stunning sunny day appeared at dawn !....missed the high tide by 2 hours this afternoon - surf a touch far out- difficult to 'sea - but - still managed to squeeze a few waves out of the session...(Sun + Fun + Family + Friends) = Great Life ...
https://www.youtube.com/watch?v=QlRGhAvMaFA
#7581
Join Date: May 2009
Location: Cape Towm, SOUTH AFRICA
Posts: 2,769
Likes: 0
Received 0 Likes
on
0 Posts
#7582
Senior Member
Join Date: Aug 2012
Location: sydney, AUSTRALIA
Posts: 388
Likes: 0
Received 0 Likes
on
0 Posts
ronkytonk
nice work on the shark.
just in case you feel as though there is so much work and re-work to get it going, and maybe feel a bit snowed under, try this quick vid
http://www.youtube.com/watch?v=Nv-OQm8d53Y
nice work on the shark.
just in case you feel as though there is so much work and re-work to get it going, and maybe feel a bit snowed under, try this quick vid
http://www.youtube.com/watch?v=Nv-OQm8d53Y
#7583
Member
Join Date: Feb 2011
Location: Calgary, AB, CANADA
Posts: 45
Likes: 0
Received 0 Likes
on
0 Posts
https://www.youtube.com/watch?v=E0vGdpukpRM I was thinking on giving my dude a GoPro head..
I think I am ready to clean my Shark up and seal it with epoxy and I should be ready to rock..
P.S. I love the SNOW!!
Last edited by ronkytonk; 03-28-2014 at 07:00 AM.
#7584
Senior Member
Join Date: Oct 2006
Location: Wilmington,
NC
Posts: 271
Likes: 0
Received 0 Likes
on
0 Posts
Heres a pic of added weight . Stock steel was 157g. I ended up putting 258 g back with gorilla glue. I have a flex shaft combo heading my way . Does anyone have a pic of a leopard motor mounted .
#7585
Senior Member
Join Date: Oct 2006
Location: Wilmington,
NC
Posts: 271
Likes: 0
Received 0 Likes
on
0 Posts
YPC do you hard mount your figure? NM I saw your post about epoxing figure but what are the made of ? Something less solid as nqd Lisa ? I plan on hard mounting mine .
Last edited by Darkseacret; 03-28-2014 at 06:44 PM.
#7586
Join Date: May 2009
Location: Cape Towm, SOUTH AFRICA
Posts: 2,769
Likes: 0
Received 0 Likes
on
0 Posts
link showing Bro's make up and mounting process: http://www.rcuniverse.com/forum/rc-b...l#post11603215
#7587
Join Date: May 2009
Location: Cape Towm, SOUTH AFRICA
Posts: 2,769
Likes: 0
Received 0 Likes
on
0 Posts
Build Progress: http://www.rcuniverse.com/forum/rc-b...l#post11771053 link for more details of process.
#7589
Join Date: May 2009
Location: Cape Towm, SOUTH AFRICA
Posts: 2,769
Likes: 0
Received 0 Likes
on
0 Posts
#7590
Join Date: May 2009
Location: Cape Towm, SOUTH AFRICA
Posts: 2,769
Likes: 0
Received 0 Likes
on
0 Posts
Sunday Arvi session ....... Good demonstration of how changing the fin choice - changes the ride of the board to better suite the conditions....
https://www.youtube.com/watch?v=efhAoqRyTaM
https://www.youtube.com/watch?v=efhAoqRyTaM
#7591
Join Date: May 2009
Location: Cape Towm, SOUTH AFRICA
Posts: 2,769
Likes: 0
Received 0 Likes
on
0 Posts
#7592
Join Date: May 2009
Location: Cape Towm, SOUTH AFRICA
Posts: 2,769
Likes: 0
Received 0 Likes
on
0 Posts
[h=2]Monday Arvi Session[/h]
#7593
Senior Member
Join Date: Oct 2006
Location: Wilmington,
NC
Posts: 271
Likes: 0
Received 0 Likes
on
0 Posts
Nice videos YPC . Bro diffently kills it .
So after a sleepless night ive decided to keep the figure o- ring tethered and reinforce the lid and try to find some small wing nuts.
So after a sleepless night ive decided to keep the figure o- ring tethered and reinforce the lid and try to find some small wing nuts.
#7594
Join Date: May 2009
Location: Cape Towm, SOUTH AFRICA
Posts: 2,769
Likes: 0
Received 0 Likes
on
0 Posts
New Build looking Good !....more detailed steps: http://www.rcuniverse.com/forum/rc-b...l#post11773181
#7595
Join Date: May 2009
Location: Cape Towm, SOUTH AFRICA
Posts: 2,769
Likes: 0
Received 0 Likes
on
0 Posts
Had 'another' sweet session this afternoon .... It's amazing what 20 minutes of rc Surfing can do for the mind - body and soul ... recommended daily !
https://www.youtube.com/watch?v=jNf_qU_An-M
https://www.youtube.com/watch?v=jNf_qU_An-M
#7596
Senior Member
Join Date: Oct 2006
Location: Wilmington,
NC
Posts: 271
Likes: 0
Received 0 Likes
on
0 Posts
Ordered a Leopard 3650 2290kv 6d . With free jacket. . From OSE Still waiting on flex shaft set up to arrive before sealing decks .
Last edited by Darkseacret; 04-02-2014 at 06:16 AM.
#7597
Join Date: May 2009
Location: Cape Towm, SOUTH AFRICA
Posts: 2,769
Likes: 0
Received 0 Likes
on
0 Posts
Howzit Darkseacret.....good size of motor choice....waiting ?....not the part of life I care to enjoy ..lol
Speaking of which ...it dawned on me today ! that whilst I'm out having my afternoon fix / workout/session - surf permitting ! - some good folk are stuck in the traffic - patiently waiting to get home...
Nick did some 'deep sea fishing'.....
https://www.youtube.com/watch?v=dJE-8BdprNI
Speaking of which ...it dawned on me today ! that whilst I'm out having my afternoon fix / workout/session - surf permitting ! - some good folk are stuck in the traffic - patiently waiting to get home...
Nick did some 'deep sea fishing'.....
https://www.youtube.com/watch?v=dJE-8BdprNI
#7598
Senior Member
Join Date: Oct 2006
Location: Wilmington,
NC
Posts: 271
Likes: 0
Received 0 Likes
on
0 Posts
#7599
Join Date: May 2009
Location: Cape Towm, SOUTH AFRICA
Posts: 2,769
Likes: 0
Received 0 Likes
on
0 Posts