Favorite/Least Favorite thing to wrench
#1
Favorite/Least Favorite thing to wrench
This might be a failed thread, but here goes.....;-)
Favorite things to wrench on:
1. Clutch setup: I got bored and timed myself the other day. I was able to take my OS engine off, change the clutch springs and put everything back together in six minutues. ;-)
2. Gear mesh: (kind of part of #1) but this is so simple I cannot understand how folks struggle with this.
3. Rebuilding diffs: I hate getting to them, but love taking them apart and re-building them.
Least favorite things to wrench on:
1. Linkage: A lot has to do with the fact I have big-***** paws and my eye-sight is shot, so it usually takes me a little while to build a linkage system with all those small parts.
2. Tire gluing. I'm just not good at this. I'll pay the few extra bucks to have them pre-mounted.
3. Rebuilding pull-starts. I've rebuilt quite a few, and eachtime have become a more bitter person because of it. Ugh!
I'd love to hear you favorite/least favorites things to work on re: your rc vehicles.
#2
My Feedback: (3)
RE: Favorite/Least Favorite thing to wrench
My tastes are odd, but since you asked...
I like:
Installing new electronics (servos, ESCs, receivers, running wires, etc.)
Gluing tires
Adjusting suspension
Trimming new bodies
(Note these are all realatively simple tasks)
I dislike:
Painting new bodies (unless it's a 1 or 2 color scheme)
Completely rebuilding shocks
Tearing down transmissions
Making small solder joints
(Note these are either tedious or time consuming tasks)
I like:
Installing new electronics (servos, ESCs, receivers, running wires, etc.)
Gluing tires
Adjusting suspension
Trimming new bodies
(Note these are all realatively simple tasks)
I dislike:
Painting new bodies (unless it's a 1 or 2 color scheme)
Completely rebuilding shocks
Tearing down transmissions
Making small solder joints
(Note these are either tedious or time consuming tasks)
#3
RE: Favorite/Least Favorite thing to wrench
I like:
painting bodies
trimming bodies
working on the general drive chain
I dislike working on:
gluing tires
and anything on my merv...
painting bodies
trimming bodies
working on the general drive chain
I dislike working on:
gluing tires
and anything on my merv...
#4
RE: Favorite/Least Favorite thing to wrench
No such thing as odd tastes. To you gluing tires is relatively easy, to me building shocks is. ;-) I'm also one of the worst at trimming bodies. Everyone has their own talents and patience for that talent.
#5
RE: Favorite/Least Favorite thing to wrench
ORIGINAL: JohnP2
No such thing as odd tastes. To you gluing tires is relatively easy, to me building shocks is. ;-) I'm also one of the worst at trimming bodies. Everyone has their own talents and patience for that talent.
No such thing as odd tastes. To you gluing tires is relatively easy, to me building shocks is. ;-) I'm also one of the worst at trimming bodies. Everyone has their own talents and patience for that talent.
I've had some that were a breeze to glue
others that my fingers were in pain after having to force the rubber off the rim so I could get glue under.
#7
RE: Favorite/Least Favorite thing to wrench
ORIGINAL: t-max97
I hate having to fix pull starts, I don't mind anything else.
I hate having to fix pull starts, I don't mind anything else.
#8
RE: Favorite/Least Favorite thing to wrench
favorite:
1. building brushed motors
2. painting body's
3. building ball diff's
least favorite:
1. uhhh... doesn't exist. i like to meticulously tinker with stuff. not getting to, or not having to build or fiddle with my car's is what i don't like. the better my cars run, the less likely i am to use them.
#9
Moderator
My Feedback: (1)
Join Date: May 2010
Location: A place in a place.
Posts: 4,197
Likes: 0
Received 0 Likes
on
0 Posts
RE: Favorite/Least Favorite thing to wrench
I like;
Installing motors
Building kits
Taking apart the whole rc car.
I deeply hate;
Putting back together the rc car.
soldering (the gun I use is 5 pounds)
gluing tires.
#10
Senior Member
My Feedback: (9)
Join Date: Nov 2008
Location: White,
GA
Posts: 1,958
Likes: 0
Received 0 Likes
on
0 Posts
RE: Favorite/Least Favorite thing to wrench
ORIGINAL: JohnP2
I've seen a few folks on here claiming to fix them in a manner of seconds. For those that can do that, you are missing a golden opportunity to charge $10.00 +shipping to fix for people. It's cheaper than buying a new one. I imagine you'd get a lot of business.
ORIGINAL: t-max97
I hate having to fix pull starts, I don't mind anything else.
I hate having to fix pull starts, I don't mind anything else.
#11
Member
Join Date: Dec 2012
Location: clarkston, WA
Posts: 38
Likes: 0
Received 0 Likes
on
0 Posts
RE: Favorite/Least Favorite thing to wrench
there is not much i dont like to do. love turning "wrenches" on my rigs.....but i do hate working on rc's if they have philips head screws. or trimming bodies
#13
Senior Member
RE: Favorite/Least Favorite thing to wrench
I hate wrenching period. The worst though are(in no particular order - I hate all of them..):
1.) Diffs
2.) Clutch*
3.) Linkage (I'm getting better at that though..)
4.) Tire glueing
5.) Body cutting, painting, and dremeling
6.) Shock building and oil changing
7.) Air filter maintenance*
8.) Dicking around with stripped screws
Wrenching though is kind of like jogging. It's like pulling teeth when you're doing it, but it feels kind of good when you're done.
I kind of like building kits when everything's new and clean though.
If I lived in a house with a yard and garage, and had an air compressor to clean stuff up better, wrenching could be made more palatable - or at least less awful. As is though I'm stuck in a flat in a tiny little corner of a room with very little space.
Probably the single worst thing I ever have to do is replace an LST2 steering servo. In general the LST2 is easy to work on for an MT - but those steering servos are a massive PIA to get in and out.
* Nitro-specific, yes. But soldering is worse than that whole list combined.
1.) Diffs
2.) Clutch*
3.) Linkage (I'm getting better at that though..)
4.) Tire glueing
5.) Body cutting, painting, and dremeling
6.) Shock building and oil changing
7.) Air filter maintenance*
8.) Dicking around with stripped screws
Wrenching though is kind of like jogging. It's like pulling teeth when you're doing it, but it feels kind of good when you're done.
I kind of like building kits when everything's new and clean though.
If I lived in a house with a yard and garage, and had an air compressor to clean stuff up better, wrenching could be made more palatable - or at least less awful. As is though I'm stuck in a flat in a tiny little corner of a room with very little space.
Probably the single worst thing I ever have to do is replace an LST2 steering servo. In general the LST2 is easy to work on for an MT - but those steering servos are a massive PIA to get in and out.
* Nitro-specific, yes. But soldering is worse than that whole list combined.
#14
Senior Member
My Feedback: (1)
RE: Favorite/Least Favorite thing to wrench
I'm fairly anal with my stuff and a bit of a perfectionist so it goes without saying I like to wrench on my stuff. What I like least is diffs I suppose. I also don't like working on my stuff if I don't have new stuff to fix it. Even one mildly worn out screw or nut just won't do! Also don't like it if I don't have enough time to do the job from start to finish. I have to many hobby's going and it seems never enough time! What I like most is getting evrything nice and clean and dialed and then taking her out and letting it rip!
#15
Senior Member
Join Date: Mar 2005
Location: Kingston UK, but living in Athens, GREECE
Posts: 18,082
Likes: 0
Received 3 Likes
on
3 Posts
RE: Favorite/Least Favorite thing to wrench
Easy...
Like wrenching on: Anything with a standard 1/8th chassis layout.
Hate wrenching on: 1/5ths in general, but the HPI Baja 5b takes the cake as the worst car to work on in history.
As for specific tasks:
Love:
Building an Xray kit
Soldering
Painting bodies
Hate:
Building shocks
Building diffs
Gluing tires
If I still did nitro at all, clutch assembly/disassembly and engine break-in would be up there in the 'Hate' section too, along with 'charging more batteries to run nitro than I need for my electrics'
Like wrenching on: Anything with a standard 1/8th chassis layout.
Hate wrenching on: 1/5ths in general, but the HPI Baja 5b takes the cake as the worst car to work on in history.
As for specific tasks:
Love:
Building an Xray kit
Soldering
Painting bodies
Hate:
Building shocks
Building diffs
Gluing tires
If I still did nitro at all, clutch assembly/disassembly and engine break-in would be up there in the 'Hate' section too, along with 'charging more batteries to run nitro than I need for my electrics'
#16
Senior Member
RE: Favorite/Least Favorite thing to wrench
Nitro engine break-in is much much easier with preheating. 3-shoe clutches are kind of a pain, but a Fioroni slider for ex., or some of the four-shoe quick-change clutches are much, much easier.. For 25 engines and bigger, put a Fioroni slider on it and pretty much forget about clutch maintenance forever - except bearings every couple gallons. Really, really easy and low maintenance. Takes clutches off the list for me.
#17
Senior Member
Join Date: Aug 2006
Location: , UNITED KINGDOM
Posts: 483
Likes: 0
Received 0 Likes
on
0 Posts
RE: Favorite/Least Favorite thing to wrench
pulls starts are simple for me as i had to take my old kyosho one apart so many times. but now i hate doing anything to a car as i have lost the use of one thumb. anyone know of a good alloy replacement . LOL
#18
Senior Member
Join Date: Mar 2005
Location: Kingston UK, but living in Athens, GREECE
Posts: 18,082
Likes: 0
Received 3 Likes
on
3 Posts
RE: Favorite/Least Favorite thing to wrench
Ha, the power of speech and opposable thumbs is what separates humans from the great apes. You're halfway DEvolved back to apedom! lol. Just kidding, what happened though if you don't mind me asking?
#19
Senior Member
RE: Favorite/Least Favorite thing to wrench
I like
- building kit from scratch
-replacing suspension arms, carriers, hubs cause its easy
I hate
-assembling turnnbuckles onto rod ends
-meshing diff ring and pinion gears
#21
Senior Member
My Feedback: (9)
Join Date: Nov 2008
Location: White,
GA
Posts: 1,958
Likes: 0
Received 0 Likes
on
0 Posts
RE: Favorite/Least Favorite thing to wrench
ORIGINAL: supertib
working on a Revo or Savage......... nothing worse !
working on a Revo or Savage......... nothing worse !
#22
Senior Member
My Feedback: (4)
Join Date: Aug 2011
Location: horseheads, NY
Posts: 2,643
Likes: 0
Received 0 Likes
on
0 Posts
RE: Favorite/Least Favorite thing to wrench
Likes:
Messing with BL motors
ESC's
Building/takign apart diffs
Putting new tires on
Hates:
Soldering wires/connectors
Taking apart/rebuilding transmissions
Removing transmissions and dogbones from Flux XS.
The process of removing tires is a bitc*!
That's pretty much it. I don't mind doing anythign else on an RC.
Messing with BL motors
ESC's
Building/takign apart diffs
Putting new tires on
Hates:
Soldering wires/connectors
Taking apart/rebuilding transmissions
Removing transmissions and dogbones from Flux XS.
The process of removing tires is a bitc*!
That's pretty much it. I don't mind doing anythign else on an RC.
#23
RE: Favorite/Least Favorite thing to wrench
The only thing I don't like is glueing tires. I usually end up with fingers glued together or to the tire. Highly irritating.
on a side note I would like to wrench my ex wife upside her skull with a heavy wrench, just saying
on a side note I would like to wrench my ex wife upside her skull with a heavy wrench, just saying
#25
RE: Favorite/Least Favorite thing to wrench
ORIGINAL: Ttam Says Blarg
Why does everyone hate gluing tires..? I've never had a problem lol.
Why does everyone hate gluing tires..? I've never had a problem lol.
softer tires I find pretty easy hard tires I can't stand doing.