***OFFICIAL*** RXB-1 THREAD
#155
RE: ***OFFICIAL*** RXB-1 THREAD
I have a problem with my RXB-1 that I have Not been able to Solve......
The engine WILL NOT Prime.......(.21 Go engine...)
I prime my engines by removing the fuel line on the Exhaust and blowing into it til the nitro reaches the carb.
This method does not WORK with this Buggy. Fuel WILL NOT flow into the engine, no matter how much pressure you apply to the exhaust line.
The only way the engine runs is to pour a small amount of fuel into the carb barrel. It starts up fine and I reattach the fuel line (engine still running), but the engine dies as soon as the fuel (that was poured into the carb) is used up. The Running engine WILL NOT suck fuel into the carb......
Here is what I have established so far......
The engine will start and run fine as long as I Physically pour gas into the carb throat.
I removed the Fuel Filter.....ran fresh fuel line.....
I have tried 3 replacement gas tanks,,,all with the same results.
I disassembled the carb,,,,and it LOOKS OK,,,,(no obvious defects )
I have not taken the engine apart, (but it runs fine).
I am at a Loss and need some help......
The engine WILL NOT Prime.......(.21 Go engine...)
I prime my engines by removing the fuel line on the Exhaust and blowing into it til the nitro reaches the carb.
This method does not WORK with this Buggy. Fuel WILL NOT flow into the engine, no matter how much pressure you apply to the exhaust line.
The only way the engine runs is to pour a small amount of fuel into the carb barrel. It starts up fine and I reattach the fuel line (engine still running), but the engine dies as soon as the fuel (that was poured into the carb) is used up. The Running engine WILL NOT suck fuel into the carb......
Here is what I have established so far......
The engine will start and run fine as long as I Physically pour gas into the carb throat.
I removed the Fuel Filter.....ran fresh fuel line.....
I have tried 3 replacement gas tanks,,,all with the same results.
I disassembled the carb,,,,and it LOOKS OK,,,,(no obvious defects )
I have not taken the engine apart, (but it runs fine).
I am at a Loss and need some help......
#159
Senior Member
My Feedback: (1)
Join Date: Mar 2008
Location: North Canton,
OH
Posts: 741
Likes: 0
Received 0 Likes
on
0 Posts
RE: ***OFFICIAL*** RXB-1 THREAD
if you disconnect the fuel line from the carb and blow into the pressure line from the exhaust, does fuel flow out of the disconnected hose? if you blow into a hose connected to the carb, can you blow through the carb? have you tried blowing on the pressure line from the exhaust with the remote at WOT?
#160
RE: ***OFFICIAL*** RXB-1 THREAD
ORIGINAL: bkfamily1
if you disconnect the fuel line from the carb and blow into the pressure line from the exhaust, does fuel flow out of the disconnected hose? if you blow into a hose connected to the carb, can you blow through the carb? have you tried blowing on the pressure line from the exhaust with the remote at WOT?
if you disconnect the fuel line from the carb and blow into the pressure line from the exhaust, does fuel flow out of the disconnected hose? if you blow into a hose connected to the carb, can you blow through the carb? have you tried blowing on the pressure line from the exhaust with the remote at WOT?
No to the second question.......
The third question: Yes, and at WOT ,,,,I am getting some flow.....
#161
Senior Member
My Feedback: (1)
Join Date: Mar 2008
Location: North Canton,
OH
Posts: 741
Likes: 0
Received 0 Likes
on
0 Posts
RE: ***OFFICIAL*** RXB-1 THREAD
if fuel flows when it is not connected to the carb, it sounds like there is something plugged or blocked in the carb or like one or more of the needles are so far closed that you can't get any flow - Eddie, would it be the HSN that controls flow at idle? or the LSN? does the Go carb have a mid range needle? any idea on starting needle settings for break in?
#162
RE: ***OFFICIAL*** RXB-1 THREAD
New update......
when the carb is in the idle position,,,,,I cannot blow fuel into the engine (clogged or closed).....even though I can SEE that the carb is open enough that fuel should flow.....
When I OPEN the carb (using radio trim) The fuel flows and the motor runs, but there is Obviously something wrong with the Carb,,,,or the way it is set up....
I will go through the Linkage and Needle set up again and see if I can figure out what is going on.....
when the carb is in the idle position,,,,,I cannot blow fuel into the engine (clogged or closed).....even though I can SEE that the carb is open enough that fuel should flow.....
When I OPEN the carb (using radio trim) The fuel flows and the motor runs, but there is Obviously something wrong with the Carb,,,,or the way it is set up....
I will go through the Linkage and Needle set up again and see if I can figure out what is going on.....
#163
Thread Starter
RE: ***OFFICIAL*** RXB-1 THREAD
the high needle controls the fuel going to the carb then the low needle control the idle to about 1/2 throttle. Sounds like something is clogging the hsn. I would take it out completely, blow some fuel thru the line, plug the top with my finger and blow some more fuel thru it, maybe even take the lsn out too, sounds like something is clogging it.
3 out on the high and 2 1/2 out on the low is a good starting point on any rc engine.
3 out on the high and 2 1/2 out on the low is a good starting point on any rc engine.
#165
RE: ***OFFICIAL*** RXB-1 THREAD
Lol....I stopped using Pal Talk because I kept getting Nasty Trojans and Viruses......
Thats kinda funny,,,,,cuz I got someThing that is trying to take over my computer right now.....Dang It!
Whatever it is,,,,it wont let me run Norton (which didnt do its job anyway) or add or delete ANY programs......
I,m gonna have to Wipe the hard drive and start over.....
I am taking the buggy to work tomorrow. I will take the carb apart and see where the clogg is.
Thats kinda funny,,,,,cuz I got someThing that is trying to take over my computer right now.....Dang It!
Whatever it is,,,,it wont let me run Norton (which didnt do its job anyway) or add or delete ANY programs......
I,m gonna have to Wipe the hard drive and start over.....
I am taking the buggy to work tomorrow. I will take the carb apart and see where the clogg is.
#167
RE: ***OFFICIAL*** RXB-1 THREAD
Update......
Made some linkage adjustments.....Made some carb adjustments.....(the carb is Sticking a bit,,,will have to monitor THAT carefully)....
Got her running though....Put a quarter tank through the engine,,,,,when I started having some radio Problems......
Might just be batteries or a loose crystal....Will check into That and keep you guys Posted.
Made some linkage adjustments.....Made some carb adjustments.....(the carb is Sticking a bit,,,will have to monitor THAT carefully)....
Got her running though....Put a quarter tank through the engine,,,,,when I started having some radio Problems......
Might just be batteries or a loose crystal....Will check into That and keep you guys Posted.
#169
RE: ***OFFICIAL*** RXB-1 THREAD
Thanks Randy,,,,,I Might take ya up on that......
There is definitely something Hinky goin on with this Carb.......
But I'm not ready to give up (stubborn as a Mule) on it yet...
There is definitely something Hinky goin on with this Carb.......
But I'm not ready to give up (stubborn as a Mule) on it yet...