1/10th ep gearing
 

Hey guys just wanted some input on thisadapter I found at 3racing. I am hoping it will work on our ep powered cars.

Just wanted your guys opinion beforeI ordered it.



http://www.3racing.hk/products.php?products_key=3477

RE: 1/10th ep gearing
 

i dont know if it will work or not

RE: 1/10th ep gearing
 

I emailed them hoping to get some dimensions, I am pretty sure it wont work for the mega e series but I believe it might  :eek: work for the older ep stuff.



</p>

RE: 1/10th ep gearing
 

These enable you to use which spur?

RE: 1/10th ep gearing
 

Yes, If it would work it will allow us to use 48p/64p spur gears. That will allowfor much diffrent gear ratios for on&amp;off road plus easier to find gears.

I am looking through tamiya stuff to try and find some specs on their spur gear holder.

RE: 1/10th ep gearing
 

keep us updated, I've been searching for 5mm bore pinions, so that i could use the brushless motors with the 5mm shaft, without much luck. I find them in 32p and 48p and even mod 0.8 and mod 1 but not mod 0.6 for some reason.
If this works out it would be a big benefit.

RE: 1/10th ep gearing
 

Found this http://www3.towerhobbies.com/cgi-bin...?&I=LXWTB0&P=7
wish they had shown what the other side looks like.

RE: 1/10th ep gearing
 

I have attached the tamiya tb03 manual. If you look atpg.4 illustration 2 and pg.5 illustration 3.
Looks pretty similar I believe. I cant be the only one who has attempted this ?

Man i love this hobby http://www.rcuniverse.com/forum/js/f...spinnyeyes.gif

RE: 1/10th ep gearing
 

Looks promising. I found it on e-bay and asked 3 different sellers for dimensions. will post the results if i get any answers.

RE: 1/10th ep gearing
 

Sounds good, I would order one if I knew where to get one. Tower doesnt have it and I cant find a tamiya dealer ?

Let me know if you get some dimesions

RE: 1/10th ep gearing
 

Haven't gotten any helpful answers yet.
This is the only us seller who has it on ebay
http://cgi.ebay.com/3-RACING-TAMIYA-...item3ef5c711a4

Which spur gear will fit this? most spurs i find has 3 mounting holes not four. and the tb-03 gears are either m0.6 or m0.4 which doesn't help us.

RE: 1/10th ep gearing
 

Drill press http://www.rcuniverse.com/forum/js/f...wink_smile.gif.

And I believe the 4 holes are for mounting the spurgear, My evader's have 4 mounting holes for spur gears as well.We would need this piece just to be close enough so that we can mesh some 48p or 64p gears.

I dont believe it would be a bolt on deal anyway.

RE: 1/10th ep gearing
 

I ordered it this morning.
 After taking the xb10 apart (to clean)  I believe it will work. Might have to shim +/- a little .

RE: 1/10th ep gearing
 

keep us up to date bro!!

RE: 1/10th ep gearing
 

Well between the lathe and a drill press it will work or I will break something :D

RE: 1/10th ep gearing
 

THATSTHESPIRIT!!!

RE: 1/10th ep gearing
 

Still waiting on adapter :eek:</p>

  I the have XB10 and Emxt both tore down just waiting on a little adapter. Hopefully something shows today.</p>

RE: 1/10th ep gearing
 

Adapter didnt ship untill the 24th http://www.rcuniverse.com/forum/js/f...ngry_smile.gif. Boughtand paid for on the 15th ?

I cant wait to leave feedback http://www.rcuniverse.com/forum/js/f...eeth_smile.gif.

But I did something constructive, maybe ?

I counted the gears inside the diff (emxt) and if my math is correct (lol) the old ep stuff should have a internal gear ratio of3.16 .

pinion gear 12t diff gear 38t

Just in case anyone wanted to know.

RE: 1/10th ep gearing
 

i hope you get it soon. be sure to post pics when you do!

RE: 1/10th ep gearing
 

The way to determine what gear ratio you have is to count the number of teeth on the ring gear and the pinion. Divide the number of pinion teeth into the number of ring gear teeth and that is your gear ratio.

RE: 1/10th ep gearing
 

Did you get it to work?

RE: 1/10th ep gearing
 

I am currently at work http://www.rcuniverse.com/forum/js/f...unge_smile.gif.

Butthe wife called to tell me it did come in so I will know if it is a drop in fit tonite.

RE: 1/10th ep gearing
 

ok, hope it works!
post plenty pics if it does.

RE: 1/10th ep gearing
 

Success.

Direct fit. Well almost. The pin that runs through the shaft will come out if you dont close the ends on the new adapter.

The smallest spur gear I have in 48p is 78. Rubs soI will have to dremel a little. Proably wont be able to use one any larger because it rubs the chassis.

Pictures to follow soon.

Will need to dremel upper support plate also. minor stuff.

RE: 1/10th ep gearing
 

Here are a few pictures.

Had to remove 2 shims from shaft so motor mount would line up. Try and get some running pictures 2morrow.

Should help onroad guys get proper gearing for t/c racing. Also if you just want to use 48/64 pitch gears.