POST A PIC OF YOUR DRIFTER THREAD!!!!!!!!!
#2755
Right now it is currently set up as 50/50 with a solid rear axle and a front one way.
Contemplating on doing a CS gears 1.5 or 1.77
I have not made any good videos of it drifting... But I can tell you it drifts awesome, just a little faster than everyone else lol.
Contemplating on doing a CS gears 1.5 or 1.77
I have not made any good videos of it drifting... But I can tell you it drifts awesome, just a little faster than everyone else lol.
#2759
My drifter started life as a Tamiya TT-01 Ferrari Enzo kit. It was never built with the intention of racing built mainly so I could run it with my son and to amuse myself at car shows during lag time. The Enzo wasn't redneck enough so I switched to a Trans Am. I am building a 3 Racing chassis to put under it for track only use only. This is the parking lot flogger sitting on the stock TT-01 chassis tub with a Tazer 12T ESC, Savox SC-0252MG servo and a Tamiya sport tuned motor. I plan on upgrading it to a brushless in the future. Axles are powered by a 3 Racing one-way unit in the front and Tamiya ball diff in the rear connected with a Tamiya aluminum drive shaft. Suspension has been upgraded with the Tamiya adjustable upper arms, low friction suspension shafts, front and rear stabilizers and a flourine coated damper set. Other upgrades are a carbon fiber upper frame, aluminum steering and link set and cooling fans for the motor and ESC.
#2760
Senior Member
Join Date: Sep 2008
Location: Harleysville, PA
Posts: 1,251
Likes: 0
Received 0 Likes
on
0 Posts
nothing special but I always wanted to try drifting. One of my customers at work bought this back in Feb and didn't use it much and sold it to me a few days ago for $75 all boxed up and some stuff not even touched in the box. There was also an Onyx 200 charger boxed up inside as well though I only have 1 nimh battery to use it with, the rest of my batts are lipo. So getting into drift with this for cheap was a good deal for me
I've run the stock nimh through it and I was hooked. Went inside and solder in deans so I could run a lipo and the car came alive again better than before. So now I've got HR strut braces, HPI aluminum prop shaft, and sway bars on the way to tinker with. Also some adjustable arms and Raikou tires are coming soon too.
I've run the stock nimh through it and I was hooked. Went inside and solder in deans so I could run a lipo and the car came alive again better than before. So now I've got HR strut braces, HPI aluminum prop shaft, and sway bars on the way to tinker with. Also some adjustable arms and Raikou tires are coming soon too.
#2762
Senior Member
Join Date: Sep 2008
Location: Harleysville, PA
Posts: 1,251
Likes: 0
Received 0 Likes
on
0 Posts
tires next weekend. Mounted the other accessories since they've arrived and took a few more shots
You can see those tires are done. I don't think T-Drifts are supposed to last from February through July lol
You can see those tires are done. I don't think T-Drifts are supposed to last from February through July lol
Last edited by 860Crawler; 08-01-2014 at 04:32 PM.
#2763
Senior Member
Join Date: Sep 2008
Location: Harleysville, PA
Posts: 1,251
Likes: 0
Received 0 Likes
on
0 Posts
Update. Ditched the Mustang body and RTR wheels. Painted up an S13 Silvia, added the Advan Oni wheels, Raikou S45 tires, HPI adjustable oil shocks and HPI universals.
Last edited by 860Crawler; 09-02-2014 at 06:09 PM.
The following users liked this post:
OGPerk503 (06-16-2020)
The following users liked this post:
OGPerk503 (06-16-2020)