RCBEE Gear & Door Sequencer
#1
Junior Member
Thread Starter
RCBEE Gear & Door Sequencer
Hi guys,
I'd like to introduce my sequencer to you. Hope you like it!
video: http://hk.youtube.com/watch?v=IzIgVnW0qiw
Website: http://www.rcbee.com
Bgds,
Koo
I'd like to introduce my sequencer to you. Hope you like it!
video: http://hk.youtube.com/watch?v=IzIgVnW0qiw
Website: http://www.rcbee.com
Bgds,
Koo
#2
My Feedback: (27)
Join Date: Dec 2002
Location: Jasper,
GA
Posts: 1,175
Likes: 0
Received 0 Likes
on
0 Posts
RE: RCBEE Gear & Door Sequencer
Looks like a nice tool ... I tried to download your manual to learn more, but it is in a .rar format. You need to convert it to something like a PDF format.
The following users liked this post:
javicuess (01-09-2023)
#7
Junior Member
Thread Starter
RE: RCBEE Gear & Door Sequencer
ORIGINAL: uncljoe
RCBEE
Are there any issues with 2.4 MHZ ?
Semper Fi
joe
RCBEE
Are there any issues with 2.4 MHZ ?
Semper Fi
joe
#9
Junior Member
Thread Starter
RE: RCBEE Gear & Door Sequencer
ORIGINAL: smokin-gun
what voltage range is it operating in.signal input, output
what voltage range is it operating in.signal input, output
Signal input is the output of receiver. Output is 5v, or supplied voltage when supplied voltage is lower than 5v.
Koo
#10
Junior Member
Thread Starter
RE: RCBEE Gear & Door Sequencer
ORIGINAL: Vincent
This is the same one that Jetlegend sells?? they have their name on it??
V..
This is the same one that Jetlegend sells?? they have their name on it??
V..
Koo
#14
Junior Member
Thread Starter
RE: RCBEE Gear & Door Sequencer
ORIGINAL: Terry Holston
Does anyone have one of these units yet? I have been trying to get one, but they wont take my Visa card.
Does anyone have one of these units yet? I have been trying to get one, but they wont take my Visa card.
Hi Terry,
Please try to enquire dreamworksrc if you haven't gotten one.
Have a nice day!
Koo
#16
My Feedback: (24)
Join Date: Dec 2001
Location: Daytona Beach
Posts: 6,102
Likes: 0
Received 0 Likes
on
0 Posts
RE: RCBEE Gear & Door Sequencer
Now in stock... http://www.dreamworksrc.com/catalog/...oducts_id=1596
Tested on JR 2.4, no operating issues detected.
Todd
Tested on JR 2.4, no operating issues detected.
Todd
#17
Junior Member
Thread Starter
#18
Junior Member
Thread Starter
RE: RCBEE Gear & Door Sequencer
If your plane doesn't need gear door closed when it is landing, e.g. F-16, so just need connect two
servosDOOR 1 and GEAR, also need to set the time from opening DOOR2 to lowering gear as "0" for
dropping gear.
http://www.rcbee.com/video2.asf
servosDOOR 1 and GEAR, also need to set the time from opening DOOR2 to lowering gear as "0" for
dropping gear.
http://www.rcbee.com/video2.asf
#19
Junior Member
Thread Starter
RE: RCBEE Gear & Door Sequencer
Set up the rotation position of the servo, and setup of reversing( actually, to exchange two positions)
http://www.rcbee.com/video3.asf
http://www.rcbee.com/video3.asf
#20
My Feedback: (44)
RE: RCBEE Gear & Door Sequencer
I just purchased the RCbee sequencer from Todd at Dreamworks and installed it in my Fei Bao Rafale
I did some experimenting with the automatic fail safe operation... this feature alone was really worth the money!!!!
No more broken Gear doors due to turning on the transmitter with the switch in the wrong position.
One comment though, the manufacturer needs to have someone proof read the English instructions.
It still will not prevent mishaps when people bump your retract switch when your jet in sitting on the ground.
Here are the test results:
Gear initially in Down position (Gear Down Storage position or Flight ready mode)
1) Transmitter Off - Turn on receiver, the audible beeper starts beeping and the gear down LED flashes, gear will stay Down.
2) Transmitter On, Gear switch in Up position - Turn on Receiver the audible beeper starts a beeping and the gear down LED flashes, gear will stay Down.
3) Transmitter On, Gear switch in Down position - Turn on Receiver audible beeper beeps once indicating normal operation and the gear down LED goes to a solid on indication, gear stay Down.
Gear initially in Up position (Gear up Storage position)
1) Transmitter Off - Turn on receiver, the audible beeper starts beeping and the gear down LED does not illuminate, gear will stay Up.
2) Transmitter On, Gear switch in Down position - Turn on Receiver the audible beeper starts beeping and the gear down LED flashes, gear will stay Up.
3) Transmitter On, Gear switch in Up position - Turn on Receiver audible beeper beeps once indicating normal operation and the gear down LED does not illuminate, gear will stay Up.
I did some experimenting with the automatic fail safe operation... this feature alone was really worth the money!!!!
No more broken Gear doors due to turning on the transmitter with the switch in the wrong position.
One comment though, the manufacturer needs to have someone proof read the English instructions.
It still will not prevent mishaps when people bump your retract switch when your jet in sitting on the ground.
Here are the test results:
Gear initially in Down position (Gear Down Storage position or Flight ready mode)
1) Transmitter Off - Turn on receiver, the audible beeper starts beeping and the gear down LED flashes, gear will stay Down.
2) Transmitter On, Gear switch in Up position - Turn on Receiver the audible beeper starts a beeping and the gear down LED flashes, gear will stay Down.
3) Transmitter On, Gear switch in Down position - Turn on Receiver audible beeper beeps once indicating normal operation and the gear down LED goes to a solid on indication, gear stay Down.
Gear initially in Up position (Gear up Storage position)
1) Transmitter Off - Turn on receiver, the audible beeper starts beeping and the gear down LED does not illuminate, gear will stay Up.
2) Transmitter On, Gear switch in Down position - Turn on Receiver the audible beeper starts beeping and the gear down LED flashes, gear will stay Up.
3) Transmitter On, Gear switch in Up position - Turn on Receiver audible beeper beeps once indicating normal operation and the gear down LED does not illuminate, gear will stay Up.
#23
Senior Member
Join Date: Nov 2008
Location: Coventry, UNITED KINGDOM
Posts: 1,015
Likes: 0
Received 0 Likes
on
0 Posts
RE: RCBEE Gear & Door Sequencer
#25
My Feedback: (21)
Join Date: Aug 2002
Location: Pottstown,
PA
Posts: 117
Likes: 0
Received 0 Likes
on
0 Posts
RE: RCBEE Gear & Door Sequencer
Thanks for the link. I will not try it,just use the AssAn I have.Thank you.
http://www.hobbyking.com/hobbyking/s...dProduct=11258
http://www.hobbyking.com/hobbyking/s...dProduct=11258