DX18 and telemetry with jetcat....?
#1
Thread Starter
My Feedback: (61)
Join Date: Sep 2002
Location: spring,
TX
Posts: 494
Likes: 0
Received 0 Likes
on
0 Posts
DX18 and telemetry with jetcat....?
just downloaded the new DX18 airware, which says it now supports jetcat data with the telemetry
i would love to install the TM1000 in a new build, if i can access the jetcat data along with rx data and batt voltage.
dont see a jetcat cable on the web site.... ??
i would love to install the TM1000 in a new build, if i can access the jetcat data along with rx data and batt voltage.
dont see a jetcat cable on the web site.... ??
#2
My Feedback: (3)
Join Date: Jun 2011
Location: Cape Coral,
FL
Posts: 31
Likes: 0
Received 0 Likes
on
0 Posts
RE: DX18 and telemetry with jetcat....?
I was looking for it and I only found them on German websites
Here is the s/n for the jetcat telemetry module from spectrum hope you can fine one state side
spma9584
Owen
Here is the s/n for the jetcat telemetry module from spectrum hope you can fine one state side
spma9584
Owen
#5
Senior Member
My Feedback: (1)
Join Date: Dec 2001
Location: Oxford, MS
Posts: 3,241
Likes: 0
Received 0 Likes
on
0 Posts
RE: DX18 and telemetry with jetcat....?
Kirk,
Chris Huhn was using it on his Ultra Bandit at Winamac, I'm pretty sure his was still a developmental version since he is one of the Spektrum managers at Horizon. You might give him a call.
DR
Chris Huhn was using it on his Ultra Bandit at Winamac, I'm pretty sure his was still a developmental version since he is one of the Spektrum managers at Horizon. You might give him a call.
DR
#6
My Feedback: (6)
RE: DX18 and telemetry with jetcat....?
Kirk,
I was just out flying with Chris Huhn yesterday and i believe that you will start seeing the Jet Cat telemetry stuff start to show up in the HH OR Spectrum web sites soon. As they just did the recent up date for the DX18 radio as of yesterday. Like DavidR has said i'm sure they wanted to make sure everything worked perfectly in the development stages before they released any product. Chris also said that with this recent up date you should be seeing much better Counts on your data logger after a flight which we did see on chris's ultra bandit yesterday after he did a flight with the update installed in his radio.
I was just out flying with Chris Huhn yesterday and i believe that you will start seeing the Jet Cat telemetry stuff start to show up in the HH OR Spectrum web sites soon. As they just did the recent up date for the DX18 radio as of yesterday. Like DavidR has said i'm sure they wanted to make sure everything worked perfectly in the development stages before they released any product. Chris also said that with this recent up date you should be seeing much better Counts on your data logger after a flight which we did see on chris's ultra bandit yesterday after he did a flight with the update installed in his radio.
#7
RE: DX18 and telemetry with jetcat....?
[link=http://www.horizonhobby.com/pdf/SPM_Telemetry_Compatibility.pdf]http://www.horizonhobby.com/pdf/SPM_Telemetry_Compatibility.pdf[/link]
#9
Thread Starter
My Feedback: (61)
Join Date: Sep 2002
Location: spring,
TX
Posts: 494
Likes: 0
Received 0 Likes
on
0 Posts
RE: DX18 and telemetry with jetcat....?
ORIGINAL: turbine guy
Now available at ''Phil's hobby shop'' on eBay ''buy now'' about $45
Now available at ''Phil's hobby shop'' on eBay ''buy now'' about $45
#10
RE: DX18 and telemetry with jetcat....?
http://www.spektrumrc.com/Products/S...rodId=SPMA9584
When operational, the JetCat sensor will measure:
throttle position,
pack voltage,
pump voltage,
EGT,
RPM, and
OFF condition.
When operational, the JetCat sensor will measure:
throttle position,
pack voltage,
pump voltage,
EGT,
RPM, and
OFF condition.
#16
My Feedback: (24)
Join Date: Dec 2001
Location: Fond du Lac,
WI
Posts: 2,234
Likes: 0
Received 0 Likes
on
0 Posts
RE: DX18 and telemetry with jetcat....?
In stock at Horizon for $39.95.........I added a GPS sensor for Ground Speed in addition to Airspeed
Sensor I have already installed in my UB.........that qualifies them for free shipping UPS ground......
Alarms are user selectable......
TA
Sensor I have already installed in my UB.........that qualifies them for free shipping UPS ground......
Alarms are user selectable......
TA
#17
RE: DX18 and telemetry with jetcat....?
Overview
The Spektrum™ SPMA9584 Aircraft Telemetry JetCat sensor is compatible with the Spektrum TM1000 Telemetry Module X-BUS expansion port.
Specifications
Type: SPMA9584 Aircraft Telemetry JetCat Sensor
Measures: Throttle position, pack voltage, pump voltage, EGT, RPM, OFF condition
Operational Voltage: 3.5 to 9.6 volts
Dimensions: 28mm x 16mm x 7mm
Weight: Circuit board - 4 gram
Calibration: No user calibration required
Units: Metric or English units
Includes:
Sensor
6-inch X-BUS extension
Key Features
Displays key turbine data including Turbine RPM, Turbine temperature, Throttle %, ECU Pack and Pump Voltage, and ECU status
Easy installation and use. Simply Plug in Jetcat sensor to ECU and TR1000 telemetry module
User defined vibration and/or tone warnings alerts users if an issue with the turbine occurs in flight
Source: http://www.spektrumrc.com/Products/D...rodID=SPMA9584
I picked one of these beauties up the other week...
Very small and very light
This is what comes in the packet
I found it worked well connecting to both my DX18 and iPad w STi
A couple more pics and description here:
http://www.rcparkflying.com/radio-co...ensor-spma9584
Anyone else using the JetCat sensor and how do you find it?
The Spektrum™ SPMA9584 Aircraft Telemetry JetCat sensor is compatible with the Spektrum TM1000 Telemetry Module X-BUS expansion port.
Specifications
Type: SPMA9584 Aircraft Telemetry JetCat Sensor
Measures: Throttle position, pack voltage, pump voltage, EGT, RPM, OFF condition
Operational Voltage: 3.5 to 9.6 volts
Dimensions: 28mm x 16mm x 7mm
Weight: Circuit board - 4 gram
Calibration: No user calibration required
Units: Metric or English units
Includes:
Sensor
6-inch X-BUS extension
Key Features
Displays key turbine data including Turbine RPM, Turbine temperature, Throttle %, ECU Pack and Pump Voltage, and ECU status
Easy installation and use. Simply Plug in Jetcat sensor to ECU and TR1000 telemetry module
User defined vibration and/or tone warnings alerts users if an issue with the turbine occurs in flight
Source: http://www.spektrumrc.com/Products/D...rodID=SPMA9584
I picked one of these beauties up the other week...
Very small and very light
This is what comes in the packet
I found it worked well connecting to both my DX18 and iPad w STi
A couple more pics and description here:
http://www.rcparkflying.com/radio-co...ensor-spma9584
Anyone else using the JetCat sensor and how do you find it?
#21
RE: DX18 and telemetry with jetcat....?
ORIGINAL: corndog2
The most important thing I think is fuel usage but it doesnt seem to do that. Nice none the less
The most important thing I think is fuel usage but it doesnt seem to do that. Nice none the less
ORIGINAL: tulz161
Quandry - No problem to have the sti and ipad connected to the same telemetry tx as the dx18?
Quandry - No problem to have the sti and ipad connected to the same telemetry tx as the dx18?
ORIGINAL: dubd
Can two sensors be adapted for twin engine applications?
Can two sensors be adapted for twin engine applications?
#23
RE: DX18 and telemetry with jetcat....?
ORIGINAL: dubd
Manual mentions daisy chaining sensors, so it gives the impression that multiple can be used.
Manual mentions daisy chaining sensors, so it gives the impression that multiple can be used.