F104 Starfighter (NASA N820) Build
#126
Thread Starter
The helmet that came with this 1/4 Premier Pilot is poor. Loads of pin holes and seam lines and generally a bad fit on every part. First step was to dismantle it rub it down and apply a coat of filler primer. I'll then fill any of the larger holes that appear and cut back ready for another coat. This will eventually be painted metallic light blue with a gloss finish.
The Little Jet Company
The Little Jet Company
#127
Thread Starter
I've finished installing 'GBR Jets' Mag Lock Vent system which I'm really impressed with! This is the 'Mag Lock Stopper' which I was sent to try. It's available soon through GBR Jets and their retail partners. Like all of their stuff its excellent quality and I'll be using them on all my future builds. Its held in magnetically and as you can see very visible even in low light. I'll never forget to remove a stopper before flight again.
The Little Jet Company
The Little Jet Company
#128
Thread Starter
I've been told that the turbine should be arriving soon so I can finally put this build to bed and start to do the ground tests before handover
Last edited by Alex48; 02-05-2014 at 08:49 AM.
#130
Thread Starter
Hi Dennis, I'm afraid not... unless he starts coming on here and commenting himself which is unlikely.
Interestingly my entire year has been booked with builds and every one is export, main land Europe mostly. I don't even think I have any models built by 'The Little Jet Company' left in the UK Shame because as a builder you get a bit attached to the stuff you produce. The 104 is destined to fly in France mostly.
Cheers, Alex
Interestingly my entire year has been booked with builds and every one is export, main land Europe mostly. I don't even think I have any models built by 'The Little Jet Company' left in the UK Shame because as a builder you get a bit attached to the stuff you produce. The 104 is destined to fly in France mostly.
Cheers, Alex
#131
" I don't even think I have any models built by 'The Little Jet Company' left in the UK Shame because as a builder you get a bit attached to the stuff you produce"
Excuse me , dont forget the little people ; ) im looking forward to getting the cougar flying again
are the maglocks etc all ready to buy now ? want to fit one to the hawk
Toby
Excuse me , dont forget the little people ; ) im looking forward to getting the cougar flying again
are the maglocks etc all ready to buy now ? want to fit one to the hawk
Toby
#132
Thread Starter
#133
Thread Starter
The Starfighters drouge chute housing is now finished and all plumbed in thanks to an Al's Hobbies delivery. I've designed an ejector that will launch the chute out once the door is open, this will hopefully guard against the possibility of the drogue chute becoming stuck in the housing.
The Little Jet Company
The Little Jet Company
Last edited by Alex48; 02-07-2014 at 01:33 AM.
#134
Thread Starter
After saying I'm not much of a fan of LED after burner effects, I'll admit to actually liking this hopefully it will look as good outside of the studio... fingers crossed!
The Little Jet Company
http://www.youtube.com/watch?v=Of2-1fiAYao
The Little Jet Company
http://www.youtube.com/watch?v=Of2-1fiAYao
#135
My Feedback: (11)
Join Date: Jan 2009
Location: azle, TX
Posts: 180
Likes: 0
Received 0 Likes
on
0 Posts
After saying I'm not much of a fan of LED after burner effects, I'll admit to actually liking this hopefully it will look as good outside of the studio... fingers crossed!
The Little Jet Company
http://www.youtube.com/watch?v=Of2-1fiAYao
The Little Jet Company
http://www.youtube.com/watch?v=Of2-1fiAYao
#136
Thread Starter
A short video demonstrating the drag chute deployment system designed for this F104 Starfighter by The Little Jet Company
http://www.youtube.com/watch?v=HCqbXvgGjJ0
http://www.youtube.com/watch?v=HCqbXvgGjJ0
#142
Alex, the chute looks very nice!
Jason, how far along are you on your 104? All my surfaces are done and the fuel tank is installed. I'm wrapping up the pipe installation tonight.
I just ordered a Details4Scale AB ring for my F-104. Looking forward to setting it up.
Jason, how far along are you on your 104? All my surfaces are done and the fuel tank is installed. I'm wrapping up the pipe installation tonight.
I just ordered a Details4Scale AB ring for my F-104. Looking forward to setting it up.
Last edited by dubd; 02-11-2014 at 08:58 AM.
#143
Thread Starter
Thanks guys, the AB ring was supplied direct from the client so I'm not sure, I'll try and find out.
I'd love to see how D4S have done the chute mechanism any pictures guys?
Hi Dubd, your going to maiden yours before mine at this rate I still haven't received the 220 yet which is all the model has been waiting for since November. Any day now I hope
Cheers, Alex
I'd love to see how D4S have done the chute mechanism any pictures guys?
Hi Dubd, your going to maiden yours before mine at this rate I still haven't received the 220 yet which is all the model has been waiting for since November. Any day now I hope
Cheers, Alex
#145
Thread Starter
The turbine has turned up Here are my initial thoughts on the JB220 straight out of the box.
The Little Jet Company
http://www.youtube.com/watch?v=tgH8Y2SeUGc
The Little Jet Company
http://www.youtube.com/watch?v=tgH8Y2SeUGc
Last edited by Alex48; 03-12-2014 at 01:49 AM.
#148
Good to hear from you too Alex, thought you'd fell out with me.
I love the new TJ, everthing including ecu inside!
Thunders the F4 along lol.
Hope things are still well with you.
I love the new TJ, everthing including ecu inside!
Thunders the F4 along lol.
Hope things are still well with you.
#149
Thread Starter
lol, no mate just really busy, I haven't flown a model since Feb last year! I very much doubt I'll be doing any flying this year either and I don't attend shows or jet meets as my schedule rarely allows for weekends. Other than not having any time I'm all good thanks. Congrats on the F4 DW said it went well