Sebart Mini Avanti w/ K45 build thread
#604
My Feedback: (34)
So where can one get a mini Avanti in the US these days ? I've been checking the JR Americas website off and on for a long time and I've never seen it show the mini Avanti as anything but back ordered. I'd love to get one if I could figure out where to get it from without having to spend a fortune to have it shipped half way around the world.
#605
My Feedback: (3)
It was surprising when I tried to order a Prometheus 2m biplane direct from Seba. He said I need to purchase it from JRA. I informed him of what JRA told me ... I'll stop there.
It's a shame. When Jason M was Sebart RC USA, getting 2m Sebart planes was never an issue.
#609
My Feedback: (7)
It would seem the only way the situation would improve is if JR Americas is no longer the SebArt distributor for the US. They certainly seem to be in a downward spiral where they have limited sales / profits so they reduce inventory and as a result get fewer orders because noting is in stock. The process repeats until nothing's left. Hope I'm wrong about that but that's how it looks from the outside..
#611
Join Date: Mar 2012
Location: Saugus, CA
Posts: 35
Likes: 0
Received 0 Likes
on
0 Posts
Jet 1a gear struts
Bob, Is this the best email for Jet 1a? ([email protected]). I sent an email to order a set of mini avanti gear and have not heard back.
Thanks
Alex Margheritis
Thanks
Alex Margheritis
#615
My Feedback: (7)
Any retailers where I can order both the CMJets tank and a Grumania pipe for the Mini Avanti? I can't read Spanish so I don't feel comfortable ordering from the CMJets site and so far my direct emails haven't been answered. The bottom line is that shipping of each item is quite expensive and if I could get them both shipped together it would be a significant savings ? Any suggestions ?
#617
Hello, for get a CMJETS tank, you can write me direc to my personal email:
[email protected]
Thank you very much in advance.
Carlos Marquez
www.cmjets.com
[email protected]
Thank you very much in advance.
Carlos Marquez
www.cmjets.com
#618
My Feedback: (7)
Thanks for the reply. I had found the pipe on the Grurmania site but it's 52 euro shipping. I suspect the shipping for the CMJets tank will be significant as well. I was hoping to find a single source that could supply both the tank and the pipe which should significantly reduce the shipping cost. I know it seems like a long shot but I figured it couldn't hurt to ask..
#619
My Feedback: (7)
Hello, for get a CMJETS tank, you can write me direc to my personal email:
[email protected]
Thank you very much in advance.
Carlos Marquez
www.cmjets.com
[email protected]
Thank you very much in advance.
Carlos Marquez
www.cmjets.com
Thanks for the reply. I had tried to email direct but I didn't get a reply. Perhaps it went to my spam folder. I've sent anther email and I'll watch carefully for your reply
#620
Join Date: Feb 2017
Posts: 70
Likes: 0
Received 0 Likes
on
0 Posts
Help with thrust tube
Hey guys,
I am starting to assemble my first turbine.
My question is I purchased a stainless thrust tube from Tamjets who seem to have gone out of business and I do not know how to support the tube.
The front of the tube has brackets and that is okay but the back of the tube floats around in the fuselage . The end of the tube is considerably smaller than the hole at the end of the fuselage.
The aircraft is a Sebart Mini Avanti and the turbine is a Kingtech K-45
I am starting to assemble my first turbine.
My question is I purchased a stainless thrust tube from Tamjets who seem to have gone out of business and I do not know how to support the tube.
The front of the tube has brackets and that is okay but the back of the tube floats around in the fuselage . The end of the tube is considerably smaller than the hole at the end of the fuselage.
The aircraft is a Sebart Mini Avanti and the turbine is a Kingtech K-45
#621
Join Date: Sep 2017
Location: Waidhofen/Thaya in Austria
Posts: 21
Likes: 0
Received 0 Likes
on
0 Posts
Hello,
I recommend this thrust tube which fits perfectly:
Schubrohr für AVANTI Mini 45 - 70 Newton - GRUMANIA JETS
Regards
Markus
I recommend this thrust tube which fits perfectly:
Schubrohr für AVANTI Mini 45 - 70 Newton - GRUMANIA JETS
Regards
Markus
#622
Hey guys,
I am starting to assemble my first turbine.
My question is I purchased a stainless thrust tube from Tamjets who seem to have gone out of business and I do not know how to support the tube.
The front of the tube has brackets and that is okay but the back of the tube floats around in the fuselage . The end of the tube is considerably smaller than the hole at the end of the fuselage.
The aircraft is a Sebart Mini Avanti and the turbine is a Kingtech K-45
I am starting to assemble my first turbine.
My question is I purchased a stainless thrust tube from Tamjets who seem to have gone out of business and I do not know how to support the tube.
The front of the tube has brackets and that is okay but the back of the tube floats around in the fuselage . The end of the tube is considerably smaller than the hole at the end of the fuselage.
The aircraft is a Sebart Mini Avanti and the turbine is a Kingtech K-45
#623
@ Jet-Lover,
are you sure the TAM jets pipe is suitable for the K45?
If it is supposed to fit the P20 it will be to narrow for the K45 and I would then suggest to order the Grumania pipe.
Best regards,
Berto.
are you sure the TAM jets pipe is suitable for the K45?
If it is supposed to fit the P20 it will be to narrow for the K45 and I would then suggest to order the Grumania pipe.
Best regards,
Berto.
#624
Join Date: Feb 2017
Posts: 70
Likes: 0
Received 0 Likes
on
0 Posts
When I ordered it, I told Tam I was using a K 45.
Would you know what the diameter is of the Grumania pipe?
#625
If you ordered at Tamjets a K45 version then it should be the right one, only a little smaller then the Grumania version.
The outside diameter of the Grumania pipe for the K45 powered Mini Avanti S is 70mm (inner about 65mm).
Whit this pipe installed the carbon rod of the stabilizer just press on the pipe and keep it in place.
Grt,
Berto.
The outside diameter of the Grumania pipe for the K45 powered Mini Avanti S is 70mm (inner about 65mm).
Whit this pipe installed the carbon rod of the stabilizer just press on the pipe and keep it in place.
Grt,
Berto.