Powerbox Core radio and set up thread.
#128
Flight Modes.
[QUOTE=AEROSHELDON;12545414]My Core was supposed to show up today but FedEx now says tomorrow. The agony! LOL When are the Flight Modes supposed to be released? Will the Core ever be set up for helis?[
An email from Richard yesterday said Flight Modes are in test now, estimated release about 3 weeks.
An email from Richard yesterday said Flight Modes are in test now, estimated release about 3 weeks.
#130
Thread Starter
Core is so clever you don’t really need FM! You can use a 3 pos switch and set separate trims on pots etc. People are flying Helis with it, again so much is possible you can set almost any crazy requirement, once you understand the unlimited possibilities.
It’s a very clever bit of kit. I’m into my second year of flying on the same prototype Tx, lots of hours of faultless operation. I visited a new club last week and was demo flying a Foam 4s BearCat that is fitted with a 7s single aerial Rx...the Spectrum guys could not believe it when I was 500m+ out at head height around the back of some trees in knife-edge! It was a spec and still felt 100% solid.
It’s a very clever bit of kit. I’m into my second year of flying on the same prototype Tx, lots of hours of faultless operation. I visited a new club last week and was demo flying a Foam 4s BearCat that is fitted with a 7s single aerial Rx...the Spectrum guys could not believe it when I was 500m+ out at head height around the back of some trees in knife-edge! It was a spec and still felt 100% solid.
#131
Core
Yes we do !
Clever as the Core mixing prgramme is, at the moment it does not allow retrimming in flight using the switch assigned to, say, flaps so that trim is automatically adjusted as flap settings are selected.
Well, I have not discivered a way !
Flight Modes are needed for this valuable function and is coming v soon.
Clever as the Core mixing prgramme is, at the moment it does not allow retrimming in flight using the switch assigned to, say, flaps so that trim is automatically adjusted as flap settings are selected.
Well, I have not discivered a way !
Flight Modes are needed for this valuable function and is coming v soon.
#133
Flight Modes
No, because my system does not allow it. Elevator trim can be assigned ONLY to the trim switches or pushbuttons. Nothing else is allowed and I have tried every switch knob and lever.
My temporary fix is to use the clever mixing system to add the pitch correction so that when flaps, controlled by switch D as on my JR systems, are operated, the elevator resets to the positions measured before installing a Core rx . That said, what I need is the ability to use the normal trim switches, pitch roll and yaw, for EACH flap setting and I am sure Flight Modes will address this.
Of course, I am still learning the system so perhaps I have missed something !
My temporary fix is to use the clever mixing system to add the pitch correction so that when flaps, controlled by switch D as on my JR systems, are operated, the elevator resets to the positions measured before installing a Core rx . That said, what I need is the ability to use the normal trim switches, pitch roll and yaw, for EACH flap setting and I am sure Flight Modes will address this.
Of course, I am still learning the system so perhaps I have missed something !
Last edited by David Gladwin; 08-24-2019 at 12:15 AM.
#135
Hi CORE community,
we added the new Kingtech / CORE ECU data converter to our known range of converters/sensor.
A brand new "Boy" with the unique feature of a complete galavnic separation for the Kingtech turbine and ECU. (Separation of the throttle channel, the telemetry channel and the power supply)
More Information under the following links:
https://www.cb-elektronics.com/p2b-kingtech---ias.html
For any question or quote don`t hesitate to contact us via our cntact page:
https://www.cb-elektronics.com/contact.html
Best regardsDirk
CB Elektronics
we added the new Kingtech / CORE ECU data converter to our known range of converters/sensor.
A brand new "Boy" with the unique feature of a complete galavnic separation for the Kingtech turbine and ECU. (Separation of the throttle channel, the telemetry channel and the power supply)
More Information under the following links:
https://www.cb-elektronics.com/p2b-kingtech---ias.html
For any question or quote don`t hesitate to contact us via our cntact page:
https://www.cb-elektronics.com/contact.html
Best regardsDirk
CB Elektronics
#139
My Feedback: (1)
A 3rd party product that protect the alcantara so it is not worn against contact with the ground: "save the lether when is down and give more estability in vertical position"
https://cmjets.com/core-print-3d-acc...port-down.html
https://cmjets.com/core-print-3d-acc...port-down.html
Bo
Loops are to lift the Tx clear of the ground. You are right that the alcantara touches the ground when its on its back. The hope I'm sure is that people are not kicking it along the ground like that ;-)
Mine after 8 months constant handling and flying, you can see the back is unmarked.
Dave
Loops are to lift the Tx clear of the ground. You are right that the alcantara touches the ground when its on its back. The hope I'm sure is that people are not kicking it along the ground like that ;-)
Mine after 8 months constant handling and flying, you can see the back is unmarked.
Dave
#143
What I did was to use the mixing to reset the elevator position for each flap position as the trim can be altered only by the trim switches or the buttons but does not change as a result of switch selection.
That said, Richard, advised me that the Flight Mode function is in the next update which is due any day now.
#147
From your post it seemed you did not have it, the latest download. Mine is downloaded and works fine so I am not sure what you are trying to achieve !!
We are all still learning !
We are all still learning !
#149
Are we going to swap info in this thread, we are all learning, so perhaps it is in our interest to do so?
I have flight modes working perfectly with the fade in function on elevator trim exactly matching flap extension speed, which should make flap operation very smooth.
3 Flight modes, flaps up, flaps 15 and flaps land with the FM allocated to the flap switch.
D.
#150
My Feedback: (99)
I would love that. I have the elevator trim set where it will move with each flap position on 3 flight modes, but I haven't tried it on the model yet (10 foot wing and in my garage) but I did not set any delay on the elevator position so I'd love to see how you did it. Seems like the thread is "set up" so sharing info is awesome.