yamahadude157

My Feedback: (1)

Hello if anyone is looking for ALUMINUM WARHEAD PARTS I found some good deals, tower hobbies is closing out some of the aluminum upgrade parts in the bargain shopper section. use this link if your interested. http://www3.towerhobbies.com/cgi-bin...&L=BARGAINSHOP

71goat

Been thinking of getting rid of all my purple aluminum and putting all plastic back on,but tower does have some good deals going on

yamahadude157

My Feedback: (1)

Why would take off the aluminum parts and put plastic back on ? Does it slow down the warhead ? If you get rid of any let me know I might buy.

DatBoiJerm

how do i get the smaller bearing off the one way transmission bearing

davido666

I just bought a new one. I couldn't get the one off mine no matter how hard I tried. They come 2 in a pack when you order them. Good Luck

davido666

Aluminum is heavier then the plastic by about 50 to 100%. To much aluminum will slow the truck down.

jayman11

If you do let me know....I'll buy the bumpers off you. Looking to use them for an experiment!

wave waker

..nothing..while waiting for my OS cooling head to come back from warranty, i got bored and looking for trouble so i installed the super pooper that been sitting for awhile, actually this motor is half done break-in when i got pissed off and junked it,,,, then fired it using starter box, man! super pooper came to life..i'l see tom if i can tamed this engine..btw, here's she is...

ssllc902

Question.

I'm either getting the axial .28 or .32 this weekend and would I still need the shim kit if I bought the .28? Also I'm not sure what to do with the shim kit once I get the engine. Where do I have to shim?

Jason

ssllc902

I aint going to miss tha dang quick start!!! Its jus another something you have to have in your hand or by your side to drive your truck. A good engine will start right aay with a primer bulb and a 1 or 2 pull of a pull start. I wish the WH hand a good pull start that did not fall apart (also if the engine was running right.).

rcbeep73

you will need to shim the clutch bell to make it fit with the spur gear. you put the shim behind the cone and in front of the bearing. it will make sence when you have all the parts in front of you.

messn03

Hey people, Mess needs yur help[sm=drowning.gif]...just bought a EVO foller off ebay w/ alot of extras but no transmission.. Does anyone have one I could buy? I dont care if it's junk 'cuz I'll re-build it w/ a FOC anyway. Appreciate anything yo can do!--Later--Mess--[:@]

messn03

Anyone know where I can find a used transmission? I just bought a roller off ebay and it doesnt have one. I'm going to look and post a "Want It" ad in marketplace. If anyone can help either respond thru the Marketplace or e-mail me @ [email protected]--Thanks to all !!!--Later-- Mess[:@]

wave waker

hey messno3, put savage 3 speed tranny there[sm=thumbup.gif],,,not sure if do-able and how hard if possible,,maybe if i get crazy i'l do it in mine.


btw, guess what, i was out running the wh with super pooper on it and man![sm=thumbup.gif] super pooper didn't put me down, though it's kinda hard during starting coz my starter box battery dies before i could start it, good that i have kwik pit starter installed but i'm using hand drill for starter not enough rpm but somehow i made it start.....engine temp stays somewhere 180-240, very consistent...ran 5-6 full tank,,,hoping tomorrow will be same...i don't trust this engine still[:-].

rcbeep73

check out my pic at my info page. did two warheads with the savage trans. i did one with the engine mounted in the front of the truck and the other in the back. the savage and wahread trans turn in different directions. depending on where you mount the engine you might have to flip the warhead diffs. it's a real nice conversion with O problems once all the work is done.

ssllc902

[quote]ORIGINAL: wave waker


its funny what a good after makert pipe does for the super pooper huh!! When I put a diffrent pipe on my super pooper I nticed i right awy it had way more torc. Bought another used WH EVO for $150 today going to go pick it up in a hr or so.

jayman11

couldnt resist picked up an Axial 32 today for $155 delivered. Hopefully I can get it in there and running quickly!

fast84stang

What is a good exhaust 4 my os.30 wh?

ssllc902

Well I did it biught a used warhead evo with a gallon ran tru it. $150 for the works with 4 extra tires and bunch of new in bag parts. Know I have twice the head probs!!!lol. Acutualy Im exiceted. Now I cn have one with the axial .28 and .32. It makes my choice alot easier. I couldnt choose betwwen the 2.lol Now I will just buy both.

wave waker

with os .30 i'm leaning towards vantage carbon fiber tuned pipe, it was featured in Car Action Magazine about the matching of os.30 with vantage tuned pipe and has a very good report.

other tuned pipe i'm leaning is the TSAIS C5H rear twin exhaust tune pipe, eversince i like the rear exhaust more realistic to me and less mess, though with this pipe i can see it needs header mods but do-able..

just my speculation the vantage tuned pipe is more both of performance and looks and the TSIAS is more on looks and functionality with performance...well, i'm getting this pipes to stop my day dreaming


rcbeep73, that's crazy i never thought somebody did that conversion, if u don't mind tell us more about it kinda interesting to me..

ok guys this is my 2nd day bashing wh with super pooper and to my surprise it's getting strong, i'm not having those engine problem so far[8D].

yamahadude157

My Feedback: (1)

Hello does anyone know of a good carburetor and pipe replacement for the stock supertigre .27

wave waker

i heard hpi carb.works ...i don't mean to sound smarty but it's not worth to invest in supertigre .27...

wave waker

hey ssll902, go bigger axial!!

try the LRP .28, i been hearing a lot of good things on this.

WARHEAD1

Hey ssllc902 do you have extra parts for the supertigre .27??

yamahadude157

My Feedback: (1)

Thanks for the response you really dont think the supertigre will go better with a good pipe. And if I buy a new motor I wouldnt want to use the stock pipe anyways right ?is the ofna .32 a good motor its 30 bones cheaper then the axial ? Thanks