Wow, I see this thread is still active. I still and will keep my CD3 which is a bad little ass ride BUT the only problem is the damn gears get torn up by rocks and pebbles. That sucks to make a few test runs and then gotta change out the gears. Anyways, good to see you guys still have the interest in 1/10 scale BB cars.

The need for speed will never cease no matter what you drive. Some move on but others will always take their place.

I haven't moved on yet. I've accomplished a lot in the last year with my 21 powered racer2 so not much else to go after. Just been trying to get everything faster now like my 90+ MPH nitro buggy. :D

How would you think my nitro tc3 would be with a fully drag modded trx 3.3 with wide foams in the rear brent ?

Brent, how would you think my dragster nitro tc3 will perform with a fully modded drag trx 3.3 with wide foam tires in the rear ?

What rear wheel adapters did you use for the nitro tc3 ?????????

DragRacer Jerrie, sorry but I don't get on here much.

I had a drag modded 3.3 in a NTC3 before and it ran just fine. Not nearly as much power as a good .21 but still ran good. You do not need wide foam tires at all. Just get a set of 40mm foams that fit 1/10th scale wheel hubs and let 'er eat.

Good luck man.

Thank you . I am using the tc3 to do drag racing around with a couple of peeps and with professionals .

Here's my monster.Its a 235mm of a colt with a dynamite platinum .21 euro edition.fastest thing I've ever owned.

Ofna colt.stupid spell check

Thats an awsome ride!....:cool:

thanks a lot man.ive had it for bout 7 years and this week was the first time ive ran her.still haven't worked all the bugs out but she flies!!!

I know what ya mean...Lol

My B-block Ld3.

http://s20.postimage.org/q91qlr3st/rc_022.jpg

looks like a handful to drive.U clocked it yet?

It is a handful,so much so that I rarely run it.Everytime I do so,it makes me into a nervous wreck.

It hasnt been clocked,but it definitly runs out of realestate in seconds,an it has to be shut down to turn it around
beforeit hits the 2 gear,If Im able to hold a straight line.It gets side ways at a half throttle punch.

Im glad that Ive seen some of the folks heres rides,now I see what type of tires their running...They are meats
that darn near go across the width of the back of the car.Now I know what tires that I will need to tame this beast...:cool:

Like your car man , it looks wicked!!

thanks nitrhead.Hey 65 what motor you running in that ld3?

Lol...I know its not much,like a modded engine,but damn its a screamer...Its just a stock 4 port 21 hyper engine.
The sleeve has lost its pinch,an I have 3 piston & sleeves.Im wanting to send in an have repinched.

However,the car will still fire up,an give me afew runs,enough to make my hands tremble...:cool:

you should mod one of the sleeves you already have.That would sure wake her up

Yea I was thinking on it,but it is offel fast already,But still would like to experiment,an push it to the limit...:cool:

I was even thinking on trying an axial 28,I have 2 of those.To see how it can handle one of them.

Hey, guys it is important that you have wide rear tires but you don't want them too wide you want them just wide enough to give you traction. If you get the rear tires too wide it may look super cool but you are just increasing your rolling resistance. 40mm wide rear tires like Brent reccomended are all you will usually need for traction and if you are running a 1/10 scale car like the NTC-3, V1RR or a HPI you won't need any adapters for these ties to fit. You can get these tires from RC-Market . They are called Xceed tires style no. 101549 wide (rear ) here is a link to their website http://www.rcmarket.com.hk/ My first parking lot racer http://www.rcuniverse.com/forum/atta...mentid=2062438http://i711.photobucket.com/albums/w...ckzilla029.jpg

Nice ride!..

Thnx man,thats a big help...:cool:

Im going to try to run it right now,going to try to adjust 2spd to shift alittle early to soften up the torq.
Try an get a vid.
I just started it,it hasnt ran in a year.Dang thing makes me nervous!

Ah nothing like hearing that fusion 3speed hittin.i had one of those myself a while back.good look on the tires too.

Thanks, Shttyn89 I liked mine too!! It had alot of Wolfpack Radicals aftermarket idems on it. I had Wolfpack 1/8 scale tire adapters on the back thats how I put those1/8 scale Serpent tires on the back.