Half Scale Nieuport 11
#277
Thread Starter
My Feedback: (38)
.....by the way, I'm not out of the woods yet - one of the hinge bearings somehow got out of round and is binding a bit on the rudder post.
CRAP! NOW I GOTTA MAKE ANOTHER ONE! (that might take another two weeks at my pace - yikes!)
looks like the seas just got a little bit rougher
#285
My Feedback: (50)
Join Date: Jun 2004
Location: Cincinnati, OH
Posts: 1,102
Likes: 0
Received 0 Likes
on
0 Posts
WOW! .....Big shocker!...Crayon a simple "C" and "Voila!" ....your done!
You know the sad part.............you will still probably only be able to muster up to put it on ONE side! LOL!
Cheers,
HPA
#289
My Feedback: (50)
Join Date: Jun 2004
Location: Cincinnati, OH
Posts: 1,102
Likes: 0
Received 0 Likes
on
0 Posts
I will post a pic of the 1/2 scale D6 when I find it later...........
HPA
Last edited by Horsepoweraviation; 04-15-2014 at 08:56 AM.
#293
Join Date: Dec 2005
Location: Victoria,
MN
Posts: 3,934
Likes: 0
Received 0 Likes
on
0 Posts
Q's.....
It looks like regular solder, not solder with a percent of silver? (silver solder) I don't know how the 2-straps on the rudder hinge will hook up, but I would think there would be some verticle forces on the rudder.
Would the solder joint give way???
I had used regular solder on 4-point gear for Piper cub on floats, and it held well, until a unexpected engine out hard landing, pulled 1-of the 4-joints out...
Perhaps brass will hold better, I used steel piano rod.
I don't want to claim it will NOT hold..... Just wondering what your thoughts on this...
It looks like regular solder, not solder with a percent of silver? (silver solder) I don't know how the 2-straps on the rudder hinge will hook up, but I would think there would be some verticle forces on the rudder.
Would the solder joint give way???
I had used regular solder on 4-point gear for Piper cub on floats, and it held well, until a unexpected engine out hard landing, pulled 1-of the 4-joints out...
Perhaps brass will hold better, I used steel piano rod.
I don't want to claim it will NOT hold..... Just wondering what your thoughts on this...
#294
Thread Starter
My Feedback: (38)
Q's.....
It looks like regular solder, not solder with a percent of silver? (silver solder) I don't know how the 2-straps on the rudder hinge will hook up, but I would think there would be some verticle forces on the rudder.
Would the solder joint give way???
I had used regular solder on 4-point gear for Piper cub on floats, and it held well, until a unexpected engine out hard landing, pulled 1-of the 4-joints out...
Perhaps brass will hold better, I used steel piano rod.
I don't want to claim it will NOT hold..... Just wondering what your thoughts on this...
It looks like regular solder, not solder with a percent of silver? (silver solder) I don't know how the 2-straps on the rudder hinge will hook up, but I would think there would be some verticle forces on the rudder.
Would the solder joint give way???
I had used regular solder on 4-point gear for Piper cub on floats, and it held well, until a unexpected engine out hard landing, pulled 1-of the 4-joints out...
Perhaps brass will hold better, I used steel piano rod.
I don't want to claim it will NOT hold..... Just wondering what your thoughts on this...
#299
Thread Starter
My Feedback: (38)
The pictures I couldn't post earlier.
This is the intended way to attach the rudder.........drill through the brass straps.........drill thru the fuse.......insert short section of dowel rod........drill thru dowel rod.......insert brass bushing into dowel......then bolt rudder to fuse.
Easier said than done...........still in the development stage.
#300
Thread Starter
My Feedback: (38)
I need to tidy up the design so that the hinges are free and the rudder is still attached firmly.
If it doesn't work out or seems like it is taking way too long (which it has already) I might just use 6 or 7 large Robart hinge points and hope that it actually will fit into the van when it is finally finished.
If it doesn't work out or seems like it is taking way too long (which it has already) I might just use 6 or 7 large Robart hinge points and hope that it actually will fit into the van when it is finally finished.