Another Ziroli Stuka build
#101
Senior Member
Thread Starter
Join Date: Sep 2006
Location: Hutsonville,
IL
Posts: 157
Likes: 0
Received 0 Likes
on
0 Posts
outer wing A coming together...port side wing here...if I have my terms right...lol looking at the front port is the right starboard is the left...
#102
Senior Member
Thread Starter
Join Date: Sep 2006
Location: Hutsonville,
IL
Posts: 157
Likes: 0
Received 0 Likes
on
0 Posts
half of wing glued ... mocked up with center ...I left the last 2 ribs off for now and the center section isn't glued...I have to wait on the Sierra landing gear...struts and wood block precut before I can glue the center...also I'm using Sig wing joiners so I have to add some shear webbing to the section between the ribs on both wing halves... this was suppose to be a one piece wing, but even with my truck I couldn't transport it...the last picture is a panoramic pic so it is a little distorted
Last edited by dalemilam58; 12-05-2014 at 08:28 AM.
#104
Senior Member
Thread Starter
Join Date: Sep 2006
Location: Hutsonville,
IL
Posts: 157
Likes: 0
Received 0 Likes
on
0 Posts
Figured out the Sig wing joiner(I hope)...added 1/8" ply between ribs 3 to 5 plus I also added 1/32" ply behind the 1/8" this should bring it flush with the other half of the joiner when I add 1/8" shear webs from rib 6 to 8...on rib 4 I had to cut the little tab off at the bottom and will fill in with a scrap piece
Last edited by dalemilam58; 12-09-2014 at 02:13 PM.
#106
Senior Member
Thread Starter
Join Date: Sep 2006
Location: Hutsonville,
IL
Posts: 157
Likes: 0
Received 0 Likes
on
0 Posts
well I think I figured out the wing joiner...I must have had it slip a fraction when I drilled it...looks like the wing tip is 1/4" higher so I just added a little more dihedral ..
#110
Senior Member
Thread Starter
Join Date: Sep 2006
Location: Hutsonville,
IL
Posts: 157
Likes: 0
Received 0 Likes
on
0 Posts
The big brown truck struck today...now on with the wing build...does anyone remember what size flashlight(torch) was used in the landing light?
#112
Senior Member
Thread Starter
Join Date: Sep 2006
Location: Hutsonville,
IL
Posts: 157
Likes: 0
Received 0 Likes
on
0 Posts
Still working on the wing...building a rear wing joiner from 1/2" aluminum channel and bar stock....using it mostly for alignment but might add a screw for strength...
#114
Senior Member
Thread Starter
Join Date: Sep 2006
Location: Hutsonville,
IL
Posts: 157
Likes: 0
Received 0 Likes
on
0 Posts
wings and fuselage together for 1st time..I epoxied the struts into the wing...after doing this I found out that the wheels would be toed out...on side more than the other...I searched and looked to find if the struts could be adjusted, after looking over the setup I found a set screw in the wheel yoke I thought I could loosen it up but when trying the whole strut turned in the block..I got the struts adjusted to a straight ahead mode with no toe in or out...hopefully this was the correct way to adjust them...
#116
Senior Member
Thread Starter
Join Date: Sep 2006
Location: Hutsonville,
IL
Posts: 157
Likes: 0
Received 0 Likes
on
0 Posts
I'll have more pictures this evening, my son just said my Christmas present just arrived and he'll bring it to me...(for a free supper of course) thanks Ed...will keep the toe in ..out..
#118
Senior Member
Thread Starter
Join Date: Sep 2006
Location: Hutsonville,
IL
Posts: 157
Likes: 0
Received 0 Likes
on
0 Posts
WOW!...I'm very impressed with http://www.sierragiant.com/ ... I bought a set of struts from them for my Stuka....I was having problems with a toe out condition...I emailed them 2 days ago explaining the problem and asking about adjustments and lack of instructions...well I just received a phone call from Darrell of Sierra ... we had a nice conversation, he explained how they were adjusted and that 3 wood screws are to be used to hold that adjustment...anyway I'm very satisfied with their customer support...
#120
Senior Member
Thread Starter
Join Date: Sep 2006
Location: Hutsonville,
IL
Posts: 157
Likes: 0
Received 0 Likes
on
0 Posts
a little more work done...little planer is great...got it at Harbor Freight in a pack of 3 for 10 bucks, needs sharpening right out of the box...
#123
My Feedback: (8)
Join Date: Mar 2011
Location: Williamsburg, VA
Posts: 105
Likes: 0
Received 0 Likes
on
0 Posts
Dale,
How's stuka coming along? I really enjoyed and appreciate your detailed pictures of wing joiners.
I'm gonna start my Stuka very soon. Finishing building table in garage, and need to order sierra gear. Hopefully I'll start this year
How's stuka coming along? I really enjoyed and appreciate your detailed pictures of wing joiners.
I'm gonna start my Stuka very soon. Finishing building table in garage, and need to order sierra gear. Hopefully I'll start this year