FW-190 D9 1/5 by fokkerc.com
#301
My Feedback: (16)
Join Date: May 2011
Location: Elizabeth, NJ
Posts: 158
Likes: 0
Received 0 Likes
on
0 Posts
Rich,
make sure to post a report on this engine. I thought about using it in my Ta152 but because of the lack of reports, decided to use the DLE 55RA which does not fit completely in the cowl. http://www.rcuniverse.com/forum/rc-w...152-h1-12.html
JG
make sure to post a report on this engine. I thought about using it in my Ta152 but because of the lack of reports, decided to use the DLE 55RA which does not fit completely in the cowl. http://www.rcuniverse.com/forum/rc-w...152-h1-12.html
JG
Sure no problem,but it will be a while,sine I have a few over projects going on now.There a pretty good thread on it on FG if you care too read.I myself was impressed with a couple of youtube video's pf a 82.5" ESM ,FW-190 Dora. Cheers: Rich
https://www.youtube.com/watch?v=7ubGtYwg7p0 https://www.youtube.com/watch?v=AJJdNJoGacU
#302
My Feedback: (2)
Join Date: Jul 2003
Location: Brisbane, QLD, AUSTRALIA
Posts: 2,787
Likes: 0
Received 8 Likes
on
4 Posts
Thanks!!!
The first vid is my Dora!
It has been an awesome engine for me. Love it to bit's and would build another model based purely on that engine alone.
Some more links for you.
https://www.youtube.com/watch?v=1P8l...wIEDw&index=14 first run of the XYZ
https://www.youtube.com/watch?v=yvE2...1BJZcl-jAwIEDw
https://www.youtube.com/watch?v=dICM...1BJZcl-jAwIEDw There is zero dampening on the camera when I took that video. just a bit of double sided tape.
https://vimeo.com/33210524
Sorry for the distraction fokke! back to the awesome 1/4 Anton and Dora's!!
Thanks
Dave
#303
Thread Starter
Don't worry Dave the engine discussion is useful for the topic
My next step is to make all scales cowls for the both models Then I will know the correct dimentions and what will fit in them
My next step is to make all scales cowls for the both models Then I will know the correct dimentions and what will fit in them
Last edited by fokke; 02-28-2015 at 01:30 AM.
#304
My Feedback: (16)
Join Date: May 2011
Location: Elizabeth, NJ
Posts: 158
Likes: 0
Received 0 Likes
on
0 Posts
Your maid video of the ESM 190 impressed the most. Imho engine runs on test stands [static runs are only good for setting idle and max power ]. Performance of a engine is best seen with the engine Loaded [married to an Airframe ] ,your aircraft performed well on it's maiden. You have a good reliable idle and smooth transaction too max power without any stumbling,good tuning job . I like you last 2 videos first time viewing them great job love the pilot head movement! On your later videos your engine is running stronger and smother and your plane is flying more scale,thanks for sharing. I need to ask you a few question if you don't mind?I know that you purchased your engine from OctopusRC, with CM-6 plus and 22-10 prop ,so I will not ask redundant questions.
Engine:
- Engine performance what is your idle and max power RPM your current set-up?
- Any upgrades,plug[I think you said you changed plugs and mufflers] what about ignition?
- Timing,did you change it,also any reed block work[Frank Bowman said some XYZ engines need a reed block mod[ little honing around reed block and or truing of reed block it self].Also some of these engines the time is off resulting in poor idle/max power performance ,should be 28 degrees before TDC report of off by 12 degrees [40 before TDC]
Airframe:
- May ask what is the total weight of your model?
- with of your cowling?
#321
My Feedback: (16)
Join Date: May 2011
Location: Elizabeth, NJ
Posts: 158
Likes: 0
Received 0 Likes
on
0 Posts
Looking good and Moving right along buddy, very nice!I couldn't wait any longer so I started working on a old Platt FW-190 Dora kit I had for years,I think I'm going too make it into a TA-150B or C.Cheers Rich
#323
Thread Starter
Thanks Z
The photographer is a good , he work for some magazines like , Vogue , Elle, Esquire and other
Here another shot
The photographer is a good , he work for some magazines like , Vogue , Elle, Esquire and other
Here another shot
Last edited by fokke; 03-16-2015 at 11:20 PM.