RCU Forums

RCU Forums (https://www.rcuniverse.com/forum/)
-   RC Warbirds and Warplanes (https://www.rcuniverse.com/forum/rc-warbirds-warplanes-200/)
-   -   New Hangar 9 1.50 P-51 Build (https://www.rcuniverse.com/forum/rc-warbirds-warplanes-200/5120982-new-hangar-9-1-50-p-51-build.html)

thrawn150 09-03-2012 05:10 PM

RE: New Hangar 9 1.50 P-51 Build
 
Sorry I do not understand are you saying to balence it at 5 5/8 inches from leading edge?

GSK 09-03-2012 05:30 PM

RE: New Hangar 9 1.50 P-51 Build
 
One inch (1") back from the leading edge of the wing at the wing tips
Graeme

djstar39 09-03-2012 05:45 PM

RE: New Hangar 9 1.50 P-51 Build
 
Mine will snap on the downside of a split S if I get too heavy handed on the elevator. Bigger airplane means bigger everything. Higher loops and split S's so that you have time on the downside to be gentle. At least that's my experience with her.

Dave

GSK 09-03-2012 05:57 PM

RE: New Hangar 9 1.50 P-51 Build
 
At the C/G setting that i have mine set at you would be hard pressed to get mine to snap .
Used to snap badly until i moved the balance forward , used to think that the beast had a bad fault ,
but really good now unless i get really slow, and i mean slow with flaps downand a 90 Deg cross wind .
Sharp pull up to avoid hitting the ground is clean with no hint of a snap at high speed .
Graeme

djstar39 09-03-2012 06:08 PM

RE: New Hangar 9 1.50 P-51 Build
 
Interesting Graeme! Will take a look at the possibility of moving mine forward. A heavier gasser hanging up there vs the 220 will help in that area. :)

Dave

GSK 09-03-2012 07:25 PM

RE: New Hangar 9 1.50 P-51 Build
 
I kinda think that theDLE 30 will, be lighter than the 220 you have in it now , that is how i found the c/g was out on mine .
Anyway you will be impressed just how much better it flies .
Graeme

djstar39 09-03-2012 08:38 PM

RE: New Hangar 9 1.50 P-51 Build
 
Graeme,

I just did some quick checking and I think you are correct. The Saito 220 is 40.5 ounces with the muffler. The DLE30 is 38.3 ounces with the muffler and ignition. The saito is 3.5hp and the DLE30 is 3.7hp. And a whole lot cheaper to run than glow fuel.

Thanks! This is giving me a lot to think about!

Dave

GSK 09-03-2012 09:00 PM

RE: New Hangar 9 1.50 P-51 Build
 
You can help get the Balance forward by using two batteries .
I usetwo 2800Li-ion Batteries with a Powerbox switch and a touch of lead (15 grams) to fine tune the setup , remembering you need a Nicad to run the box also .
you should get it spot on that way
I use about 300ma per flight , so you need large capacity cells for the servos and RX
Graeme

miklos 09-04-2012 04:41 AM

RE: New Hangar 9 1.50 P-51 Build
 
Ok, just for clarification, you are saying to balance it 1" back from the leading edge of the wingtip not where the wing root meets the fuselage?
Is that correct?


GSK 09-04-2012 11:50 AM

RE: New Hangar 9 1.50 P-51 Build
 
Yes , that is correct.
Graeme

wheels down 09-04-2012 04:05 PM

RE: New Hangar 9 1.50 P-51 Build
 
I have a RCGF 32cc
with 20x10 prop / only flow it twice / seems to have more than enough power/ only problem ,had to replace gear /cut the throttle to early
keep a little power on till the wheels touch
good luck

djstar39 09-07-2012 09:43 AM

RE: New Hangar 9 1.50 P-51 Build
 
Folks,

I'm considering the DLE 30... On my Saito 220 I'm using a Dave Brown Spinner that I will want to reuse with the DLE30. Not sure what adapter to get for that as I'm sure the threads are probably different.

Dave

Never mind, called Dave Brown Products and got the info...

djstar39 09-16-2012 07:03 AM

RE: New Hangar 9 1.50 P-51 Build
 
Graeme or Capt G, I picked up a DLE 30 and wondered if you you had any pictures of how you mounted it to get the prop shaft in the middle? No lines on the firewall so I was just going to draw lines between the existing mount to place the X on the firewall and then do the same on a piece of paper of the DLE 30 mount extensions and then just overlay the X on the paper with the X on the firewall. The mount extensions end up right up against the fuse on the port side. Sound about right?

Dave

Capt G 09-16-2012 02:35 PM

RE: New Hangar 9 1.50 P-51 Build
 
Find something to put in the fuse so you can hang it vertical. Then set the motor on the standoffs on the firewall with the spinner backplate on it and mark where the holes need to go.

microdon2 09-16-2012 02:48 PM

RE: New Hangar 9 1.50 P-51 Build
 
Have you guys thought of the DLE 35? 10% more horsepower, rear-pointed exhaust. Thin profile. From what I read on TH the rear-pointed exhaust might be specifically for tuned pipes, so maybe not for this plane. But might be worth speaking to TH about.

Fly@FQD 10-21-2012 03:27 PM

RE: New Hangar 9 1.50 P-51 Build
 
Just had the maiden flight of my Frankie. It could not have went any better. Smooth climb out.and three clicks of down elevator was the only trimming needed.
PTE36 engine ran great. Robart electric retracts worked and looked great. She settled right in for a smooth scale looking landing.Thanks for all the free advice on this forum.

SBrian 01-14-2013 11:58 AM

RE: New Hangar 9 1.50 P-51 Build
 
Where did you get that great looking pilot for you P51?

Thanks

Steve

GSK 01-14-2013 12:23 PM

RE: New Hangar 9 1.50 P-51 Build
 
Quote:' Find something to put in the fuse so you can hang it vertical. Then set the motor on the standoffs on the firewall with the spinner backplate on it and mark where the holes need to go.


Like he says
I turn 4 grub screws to a sharp point on one end , screw them into the standoffs , eyeball the spinner Smack it with a Hammer http://www.rcuniverse.com/forum/js/f...eeth_smile.gifand job done

Graeme

djstar39 01-14-2013 05:30 PM

RE: New Hangar 9 1.50 P-51 Build
 
Thanks Graeme! What an easy idea! I think I was overthinking this one.

Dave

thrawn150 08-12-2013 10:06 AM

has anyone had a issues with the stab fulling off. Someone at the field said that I should not trust the screws and I should epoxy them in, any ideas?

gweevz 08-26-2013 06:50 PM

Hello,
I have complete Hanger 9 1:50 Mustang still in box. Comes with Saito 36cc gas, Keleo exhaust, Ifltaiies pilot, Robart retract tailwheel, all the JR servos with Spektrum Dx-8 radio with spektrum case. Everything still in box, health issues forces sell. Have other kits in giant scale for sale 1/5 T/F Corsair, Mustang, and P-40 arfs. Didn't mean to interupt forum, can't seem to download on "Buy & Sell". Thank you Steven.

GSK 08-26-2013 08:44 PM


Originally Posted by thrawn150 (Post 11588821)
has anyone had a issues with the stab fulling off. Someone at the field said that I should not trust the screws and I should epoxy them in, any ideas?


I can assure you that the Stab will not fall off if you fit a wooden Dowel in the tube, then fit the screws, glue them in with Cyno .
Mine have been in for years .
Poor thing is falling apart from all the use it has had .
Graeme

waytooslow 06-11-2015 12:45 PM

Gentlemen - not to revive such an old thread - but looking for a cowl for this bird. I recently acquired this old gal and am toying with idea of a different engine than the included DLE 30. If anyone has one laying around. please let me know. Thanks Scott

thrawn150 06-15-2015 06:21 AM

I found one on ebay from AU. 20 bucks for shipping.

waytooslow 10-06-2015 10:24 AM


Originally Posted by thrawn150 (Post 12055353)
I found one on ebay from AU. 20 bucks for shipping.


just saw and nothing found when searched.


All times are GMT -8. The time now is 06:56 AM.


Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.