Valcano s30 Transmission
#1
Junior Member
Thread Starter
Join Date: Jan 2013
Location: West Seneca, NY
Posts: 20
Likes: 0
Received 0 Likes
on
0 Posts
Valcano s30 Transmission
Hi guys, I recently had to replace the 2 plastic gears in my volcano s30 transmission, I have the new gears in and before I put the trans, in I made sure the gears were working right.The problem i'm having is when I go to run the truck it only runs for a couple runs and the wheels stop turning, but the gears in the trans, are spinning and shafts are spinning when I throttle. If I pick the truck up off the ground and hit the throttle the wheels spin, same goes if I have the truck off and push the truck forward , the tires turn. also the couplers that hold the drive shafts in place are coming loose, but the set screws are still tight. I must have something put together wrong but I can't figure out what, I have the long shaft ( dog bone) in the rear and the short dog bone in the front. Thanks for any info.
#2
RE: Valcano s30 Transmission
ORIGINAL: tyler19
Hi guys, I recently had to replace the 2 plastic gears in my volcano s30 transmission, I have the new gears in and before I put the trans, in I made sure the gears were working right.The problem i'm having is when I go to run the truck it only runs for a couple runs and the wheels stop turning, but the gears in the trans, are spinning and shafts are spinning when I throttle. If I pick the truck up off the ground and hit the throttle the wheels spin, same goes if I have the truck off and push the truck forward , the tires turn. also the couplers that hold the drive shafts in place are coming loose, but the set screws are still tight. I must have something put together wrong but I can't figure out what, I have the long shaft ( dog bone) in the rear and the short dog bone in the front. Thanks for any info.
Hi guys, I recently had to replace the 2 plastic gears in my volcano s30 transmission, I have the new gears in and before I put the trans, in I made sure the gears were working right.The problem i'm having is when I go to run the truck it only runs for a couple runs and the wheels stop turning, but the gears in the trans, are spinning and shafts are spinning when I throttle. If I pick the truck up off the ground and hit the throttle the wheels spin, same goes if I have the truck off and push the truck forward , the tires turn. also the couplers that hold the drive shafts in place are coming loose, but the set screws are still tight. I must have something put together wrong but I can't figure out what, I have the long shaft ( dog bone) in the rear and the short dog bone in the front. Thanks for any info.
#3
Junior Member
Thread Starter
Join Date: Jan 2013
Location: West Seneca, NY
Posts: 20
Likes: 0
Received 0 Likes
on
0 Posts
RE: Valcano s30 Transmission
When I put the truck on the ground to run it, I hit the throttle, the transmission is spinning, the front and rear dog bones are spinning but the wheels are not spinning, if I pick the truck up off the ground and hit the throttle the wheels will spin, I tighten the set screws on the drive cups and put some blue Loctite on them also, do the drive cups go on a certain way, I think that may be my problem?
#4
RE: Valcano s30 Transmission
Hmmm,you tightened the grub screws on the drive cups but did you get the screw even with the flat spot on the output shafts coming off the transmission?
#6
RE: Valcano s30 Transmission
ORIGINAL: nitrosteve22
Hmmm,you tightened the grub screws on the drive cups but did you get the screw even with the flat spot on the output shafts coming off the transmission?
Hmmm,you tightened the grub screws on the drive cups but did you get the screw even with the flat spot on the output shafts coming off the transmission?