Redcat Racing Volcano Thread
#277
Senior Member
Join Date: Sep 2007
Location: Benton Harbor, MI
Posts: 153
Likes: 0
Received 0 Likes
on
0 Posts
RE: Redcat Racing Volcano Thread
try a new plug too I had the same problem my plug would glow but i guess it wasn't enough I put in a new one and there she went
#278
Senior Member
Join Date: Nov 2007
Location: Bridgewater,
NJ
Posts: 3,961
Likes: 0
Received 0 Likes
on
0 Posts
RE: Redcat Racing Volcano Thread
Are [link=http://redcatracing.com/itemdetail_part.asp?partno=02138]these[/link] bearings for the wheels and can they be used on the electric volcano?
#285
Junior Member
Join Date: Dec 2006
Location: chittenango, NY
Posts: 20
Likes: 0
Received 0 Likes
on
0 Posts
RE: Redcat Racing Volcano Thread
I'm looking to build two complete axles for a crawling project except I already have the diffs where can I find these parts?? arms, steering knuckles, axles carriers...........etc
#287
Senior Member
Join Date: Nov 2007
Location: Bridgewater,
NJ
Posts: 3,961
Likes: 0
Received 0 Likes
on
0 Posts
RE: Redcat Racing Volcano Thread
In case anyone wanted to know, the Volcano EPX is fully Brushless ready. I swear, all the internal tranny gears are steel. The dogbones are aluminum or steel and the drive axal is aluminum.
#288
Member
Join Date: Dec 2007
Location: Wind Gap,
PA
Posts: 39
Likes: 0
Received 0 Likes
on
0 Posts
RE: Redcat Racing Volcano Thread
heyy someone help me out. i have a redcat volcano sv. between the engine and and throttle servo where theres an axle down in there, the joint at the rear end of it under the pullstart keeps coming loose and moving around and stuff. is there a way i can fix that or do i need to take it to a hobby shop?
#289
Senior Member
Join Date: Jan 2007
Location: , PA
Posts: 5,382
Likes: 0
Received 0 Likes
on
0 Posts
RE: Redcat Racing Volcano Thread
You should locktite that and the screw that goes in it. Make sure teh screw is pretty tight also. Also put a very small peice of fuel tube on the drive cup then install teh shaft. Thjis will take up any play because these have way too much play in them.
#292
Senior Member
Thread Starter
My Feedback: (1)
Join Date: Jun 2005
Location: Clermont, FL
Posts: 2,824
Likes: 0
Received 0 Likes
on
0 Posts
RE: Redcat Racing Volcano Thread
of course it can be removed. Take off the rear(4 screws from underneath.) then take off the 2 screws on the top purple mount right above the drive cup. Then you can get the spur off.
#294
Member
Join Date: Nov 2007
Location: Surrey,
BC, CANADA
Posts: 60
Likes: 0
Received 0 Likes
on
0 Posts
RE: Redcat Racing Volcano Thread
Here are some photos of my stock SV with custom paper clip body clips
http://www.rcuniverse.com/gallery/ga...emberID=385669
http://www.rcuniverse.com/gallery/ga...emberID=385669
#296
Member
Join Date: Nov 2007
Location: Surrey,
BC, CANADA
Posts: 60
Likes: 0
Received 0 Likes
on
0 Posts
RE: Redcat Racing Volcano Thread
ORIGINAL: ehroof
looks good, what rims and tires are you using?
looks good, what rims and tires are you using?
#299
Banned
Join Date: Jan 2008
Location: Colchester,
VT
Posts: 478
Likes: 0
Received 0 Likes
on
0 Posts
RE: Redcat Racing Volcano Thread
the steering on my volcano is bad
i dont know why when its rolling or running its not any better
please help me fix it or strengthen it
heres a video of it
i dont know why when its rolling or running its not any better
please help me fix it or strengthen it
heres a video of it
Code:
<object width="425" height="355"><param name="movie" value="http://www.youtube.com/v/yvtUQ8sWPvQ&rel=1"></param><param name="wmode" value="transparent"></param><embed src="http://www.youtube.com/v/yvtUQ8sWPvQ&rel=1" type="application/x-shockwave-flash" wmode="transparent" width="425" height="355"></embed></object>