RE: Redcat Racing Volcano Thread
Which shaft is it that won't spin. The one going to the differential or the ones coming out?
|
RE: Redcat Racing Volcano Thread
going frome the tranny to the diff
|
RE: Redcat Racing Volcano Thread
So the front one is driving but the rear won't
|
RE: Redcat Racing Volcano Thread
yup
|
RE: Redcat Racing Volcano Thread
i had that same problem the oter day. I had to make sure the drive cup was line up correctly on the shaft coming from the tranny. i tightened it incorrectly on the round part of the shaft and it would slip. once we put it on the flat part no more problems.
|
RE: Redcat Racing Volcano Thread
Ya try that and if that don't work, I don't know. Usually, they both quit.
|
RE: Redcat Racing Volcano Thread
does anybody know if the Aluminum Universal Shafts are any better than the stub axles. I keep breaking the stub axles. any ideas other than taking it easy.
|
RE: Redcat Racing Volcano Thread
ORIGINAL: gg31905 does anybody know if the Aluminum Universal Shafts are any better than the stub axles. I keep breaking the stub axles. any ideas other than taking it easy. How are you breakin em? Bad Landings off Big Air?. Or are ya runnin into things and just Snappin em off? |
RE: Redcat Racing Volcano Thread
Ya I run my truck hard jumping and such[not a redcat though]and I have never broke one.
|
RE: Redcat Racing Volcano Thread
Sometimes when i start my truck up and i give it a little gas, it starts going backwards. Then i start it up again and it's just fine, Whats the deal with this??
|
RE: Redcat Racing Volcano Thread
i would say it is bad landings, not as big as air as my tmaxx, but it might be big air for these about 5' landing vertical on 1 tire
|
RE: Redcat Racing Volcano Thread
ORIGINAL: perhamrocks Sometimes when i start my truck up and i give it a little gas, it starts going backwards. Then i start it up again and it's just fine, Whats the deal with this?? |
RE: Redcat Racing Volcano Thread
sounds like the engine started backwards, it can happen, does it happen often?
|
RE: Redcat Racing Volcano Thread
Today was the only time it starded doing it, but i noticed if i rolled it forward a bit before i started it would be fine, but i also noticed my pull cord sometimes dosn't retrieve all of the cord back in, but usually on the final pull when the engine starts it goes back in.
Thanks for the help in advance ehroof, your the KING! |
RE: Redcat Racing Volcano Thread
What size is the spur gear on the stock volcano? I need to know how many teeth so i can see if my lhs has any?
|
RE: Redcat Racing Volcano Thread
ORIGINAL: perhamrocks Today was the only time it starded doing it, but i noticed if i rolled it forward a bit before i started it would be fine, but i also noticed my pull cord sometimes dosn't retrieve all of the cord back in, but usually on the final pull when the engine starts it goes back in. Thanks for the help in advance ehroof, your the KING! your welcome :D |
RE: Redcat Racing Volcano Thread
ORIGINAL: perhamrocks What size is the spur gear on the stock volcano? I need to know how many teeth so i can see if my lhs has any? 39 and i doubt you will find anything that will fit, i tried from hpi, traxxas, tamiya, kyosho. Its the same pitch as the hpi but no gears will mount like it. |
RE: Redcat Racing Volcano Thread
39 teeth[X(] Thats a weird amout of teeth on a spur gear.
|
RE: Redcat Racing Volcano Thread
so what ur saying is that i have to get it over the internet from redcat?
|
RE: Redcat Racing Volcano Thread
Yep Or if u have a hobbytown usa, they can order parts.
|
RE: Redcat Racing Volcano Thread
ORIGINAL: perhamrocks so what ur saying is that i have to get it over the internet from redcat? or from a dealer |
RE: Redcat Racing Volcano Thread
Ya that too
|
RE: Redcat Racing Volcano Thread
Is this the right direct drive for the volcano?
http://www.redcatracing.com/itemdeta...p?partno=02126 |
RE: Redcat Racing Volcano Thread
yes, you will need a 13 tooth clutch bell for it, an hpi clutch bell will work
|
RE: Redcat Racing Volcano Thread
Thanks for your help
|
All times are GMT -8. The time now is 06:23 PM. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.