RE: Redcat Racing Tsunami Thread
 

can you give me some specs and pricing on that motor and what i would need to do fitting it into my nami

RE: Redcat Racing Tsunami Thread
 

im already bored with the .18

RE: Redcat Racing Tsunami Thread
 

Oh, if you don't have the RR you might not have a mid range needle then. The mid range needle is opposite the LSN on the other side of the carb, there should be a large looking screw head. That's the Mid-Range needle. It will leak around the screw head.

RE: Redcat Racing Tsunami Thread
 

Which axial engine, the 21, 21R, 28 or 28R

RE: Redcat Racing Tsunami Thread
 

.28

RE: Redcat Racing Tsunami Thread
 

hahahahha the sh.18 has no balls at all down low or maybe that was just mine , i few pages ago i have some post of me getting it all together just have a look around page 67-68 and so on , it cos me about $200 or so all up , lol more than i payed for the car hahahaha oh well you need new engine mounts , SG clutch and flywheel kit , new throttle linkage , exhaust header and pipe , engine and thats about it . but HIMOTO USA maybe be doing a kit for every one witch would be cheaper,

RE: Redcat Racing Tsunami Thread
 

how is it on the gears and diffs?

RE: Redcat Racing Tsunami Thread
 

Hey Uhoo-01, LOL, I have the 32R not the 28r I don't know what I was thinking, that may be why you don't have the mid range, either way, lol, watch for leaks, it's the only draw back I've seen to the engine the carb O-rings leak.


retrosoul, the base model Axial 28 engines with the grey head go for about $120 and up full retail price on that engine is $265.00. The same engine with a green heads gonna run around $145(supply and demand) and up Full retail price is $265.00. Supply and demand, people like the green head better so it's more expensive, that's life, lol.

RE: Redcat Racing Tsunami Thread
 

hey guys i need help hpi makes a clutch bell 13t/to 18t two speed will it work on a redcat tsunami

RE: Redcat Racing Tsunami Thread
 

fine on the diff , and on the main gear it is hard on it but with a good mesh its fine

RE: Redcat Racing Tsunami Thread
 

Ya man it will work. 5 tooth difference = it will work.

RE: Redcat Racing Tsunami Thread
 

All this big block talk is making things happen in my pants I really want to get one now :) But the only thing that worries me is that with the cvrx im blowong bevel gears all the time so whats going to happen with a BB?????

RE: Redcat Racing Tsunami Thread
 

i am worried about the bell not being deep enough

RE: Redcat Racing Tsunami Thread
 

my new truck stand i found the folding frame in the trash!!! the things people just throw away all i did was add the wood.

http://i48.photobucket.com/albums/f2...r/IMG_8667.jpg
http://i48.photobucket.com/albums/f2...r/IMG_8666.jpghttp://i48.photobucket.com/albums/f2...r/IMG_8668.jpg
http://i48.photobucket.com/albums/f2...r/IMG_8669.jpghttp://i48.photobucket.com/albums/f2...r/IMG_8670.jpg

RE: Redcat Racing Tsunami Thread
 

Thats a sweet stand man!!!! Sell it???? lol

RE: Redcat Racing Tsunami Thread
 

any 1 want to come to new hampshire and play?

RE: Redcat Racing Tsunami Thread
 

soz man bit far for me .... lol

RE: Redcat Racing Tsunami Thread
 

what do i need to remove to get the rear drive shaft out?

RE: Redcat Racing Tsunami Thread
 

you mean the ones to each of the wheels , just take off the turnbuckles to the hubs and let the wheel drop down and they just fall out . if your talking about the rear tranny shaft you have to take the center tranny out as a whole unit

RE: Redcat Racing Tsunami Thread
 

yea i meant the rear tranny shaft and i was hoping i wouldnt have to remove that. i meshing the gears

RE: Redcat Racing Tsunami Thread
 

yeah iv taken the tranny out without moving the engine befor , you can do it , hahahah i dont no if its good for it tho . it makes it hard to get ya fingers in , to put the shaft in tho .

RE: Redcat Racing Tsunami Thread
 

i have to replace the universal cup anyways

RE: Redcat Racing Tsunami Thread
 

im gonna try and make my own universal cups out of 1700 series stainless they should last years

RE: Redcat Racing Tsunami Thread
 

good idea they look pretty eazy to machine up , its just you will prob start breaking the next thing inline like, drive shafts or what ever...

RE: Redcat Racing Tsunami Thread
 

im gonna make the drive shafts out of titanium