Searching Magazinarticel for A-26 Invader (96") Gary Fuller Semiscale out RCM 08/2004
#1
Thread Starter
Searching Magazinarticel for A-26 Invader (96") Gary Fuller Semiscale out RCM 08/2004
Hello
I look for the magazine-contribution about the model A-26 Invader in Semiscale of GaryFuller.
The best would be a Scan of the magazine-sides as return, I have the plan from this Model.
Many Thanks an sorry for my bad english
Bernd
I look for the magazine-contribution about the model A-26 Invader in Semiscale of GaryFuller.
The best would be a Scan of the magazine-sides as return, I have the plan from this Model.
Many Thanks an sorry for my bad english
Bernd
#2
Bernd...not sure I can come up with it, but I will try. Gary flies in the club I belong to and I have seen the Invader first hand. Our next meeting is in January and if he is there, I will ask. He usually attends the meetings, but it is Winter. If you can get it in the meantime, I will monitor the thread just in case.
#3
Thread Starter
Hello Hookedonrc
Thanks for your answer.I can wait also until January
Maybe somebody still reports
If no one reports, you are my single help
Many Thanks
Best Regards
Bernd
Thanks for your answer.I can wait also until January
Maybe somebody still reports
If no one reports, you are my single help
Many Thanks
Best Regards
Bernd
#4
My Feedback: (31)
Join Date: Jan 2002
Location: Battle Creek,
MI
Posts: 175
Likes: 0
Received 0 Likes
on
0 Posts
Bernd,
I can get you a hard copy of the copy of the article
via the mail if you like. Just PM your address (or e
mail me at [email protected]).
Craig
I can get you a hard copy of the copy of the article
via the mail if you like. Just PM your address (or e
mail me at [email protected]).
Craig
#8
Drcraig. Are you still looking for plans. Gary wasn't at the meeting, but I have been in touch via email. He says he has heard there are problems with RCM taking money and not delivering plans. Gary doesn't have any, but said he could probably draw them. If you are interested, I can see if he minds you working directly with him. If ok, I can give you his contact info.
#9
My Feedback: (31)
Join Date: Jan 2002
Location: Battle Creek,
MI
Posts: 175
Likes: 0
Received 0 Likes
on
0 Posts
Thanks for the offer - and thank Gary too. Asking him to draw the plans over again would be nuts!!
After I emailed the article to Bernd, he emailed me back a scan of the plan and "hemikiller" is
printing it for me. So, I think I am all set.
Thanks again.
After I emailed the article to Bernd, he emailed me back a scan of the plan and "hemikiller" is
printing it for me. So, I think I am all set.
Thanks again.
#11
Junior Member
Join Date: May 2007
Location: Wagga WaggaNew South Wales, AUSTRALIA
Posts: 1
Likes: 0
Received 0 Likes
on
0 Posts
Drcraig. Are you still looking for plans. Gary wasn't at the meeting, but I have been in touch via email. He says he has heard there are problems with RCM taking money and not delivering plans. Gary doesn't have any, but said he could probably draw them. If you are interested, I can see if he minds you working directly with him. If ok, I can give you his contact info.
I had no problem getting the full sized plans.
I'm just beginning my second build of Gary's A26. The first model was great, very easy to fly with almost trainer like characteristics. However, like all twins, it does not respond well to mishandling of asymmetric flight! The first one bit the dust. I ran Century Jets retracts and Saito 61 FS .The Saito's provided plenty of power. It looked great in the air especially when doing flat out low passes! The new model will be much the same, although I've changed to electric actuators on the retracts.
What I would like to do if possible is set up contact with Gary. Could one of you tell me how I can contact him please?
#13
Thread Starter
Hello Juan
I have the Plans uploaded to Outerzone include Magazinarticel
https://outerzone.co.uk/plan_details.asp?ID=5882
Greetings Bernd
I have the Plans uploaded to Outerzone include Magazinarticel
https://outerzone.co.uk/plan_details.asp?ID=5882
Greetings Bernd