RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Search
Today's Posts
Mark Forums Read
Vendor Directory
Notices
Search: Posts Made By: pc1972
Showing results 1 to 11 of 11
Search took 0.05 seconds.
Forum: RC Warbirds and Warplanes
11-24-2016, 11:57 AM
Replies: 75
Views: 39,931
Posted By pc1972

Hi Coxco, I've recently bought two Spektrum...

Hi Coxco,
I've recently bought two Spektrum A5060 Mini HV Digital Hi-Torque MG servos for my Mustang and I find that they are noisy when idling in the centre position. They are making a random...
Forum: RC Jets
10-30-2016, 02:00 AM
Replies: 2,625
Views: 735,649
Posted By pc1972

Hi Turbiner, I've got exactly the same setup...

Hi Turbiner,

I've got exactly the same setup as you with a Wren 80. This is my first turbine and I to have had problems with bouncy landings on our grass strip - had to replace the 6mm nose leg...
Forum: RC Jets
02-12-2015, 02:07 AM
Replies: 2,625
Views: 735,649
Posted By pc1972

Superb flying Dave - so graceful! Is this at...

Superb flying Dave - so graceful!
Is this at your local club?

Pete
Forum: RC Jets
02-11-2015, 10:44 AM
Replies: 2,625
Views: 735,649
Posted By pc1972

3mm O/D and 2mm I/D Pete

3mm O/D and 2mm I/D

Pete
Forum: RC Jets
02-05-2015, 04:39 AM
Replies: 2,625
Views: 735,649
Posted By pc1972

Cheers Dave, managed to reposition the nipples...

Cheers Dave, managed to reposition the nipples and sealed with epoxy.
Forum: RC Jets
02-04-2015, 04:56 AM
Replies: 2,625
Views: 735,649
Posted By pc1972

Hi Dave, The build of my Xcalibur is...

Hi Dave,

The build of my Xcalibur is progressing nicely but I have a few more questions if you don't mind.

This is the first model I've built with air retracts, so it's a bit of a learning...
Forum: RC Jets
02-01-2015, 08:22 AM
Replies: 2,625
Views: 735,649
Posted By pc1972

Cheers Dave, Thanks for your advice

Cheers Dave, Thanks for your advice
Forum: RC Jets
02-01-2015, 05:47 AM
Replies: 2,625
Views: 735,649
Posted By pc1972

Hi Dave, thanks for your reply. I'm in good old...

Hi Dave, thanks for your reply. I'm in good old Blighty, Bedford to be precise.

I've checked the movement on the elevator and it's fine and not stalling the servo at any point through it's...
Forum: RC Jets
01-31-2015, 10:14 AM
Replies: 2,625
Views: 735,649
Posted By pc1972

Thanks for the advice Grodus, just epoxied my...

Thanks for the advice Grodus, just epoxied my aileron hinges this afternoon and found that the hole alignment was pretty good. They were within 0.5mm, I'd say. I had to set the trailing edge of the...
Forum: RC Jets
01-31-2015, 05:33 AM
Replies: 2,625
Views: 735,649
Posted By pc1972

Hi there, I bought the model last July and I've...

Hi there,
I bought the model last July and I've finally got round to starting it! I think it's from the first batch of RAF colour scheme kits. I've also seen notes on here about dodgy metal clevises...
Forum: RC Jets
01-31-2015, 04:47 AM
Replies: 2,625
Views: 735,649
Posted By pc1972

Hi Everyone, Just started building my Xcalibur...

Hi Everyone,
Just started building my Xcalibur this week and I've come up against a potential problem. When hinging the rudders and elevator I've noticed that some of the hinge holes are off centre...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.