RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: AKA2
Showing results 1 to 10 of 10
Search took 0.04 seconds.
Forum: RC Warbirds and Warplanes
05-18-2017, 07:33 PM
Replies: 2,806
Views: 635,828
Posted By AKA2

Almost 31 lbs. Kept it stock, no extras like...

Almost 31 lbs. Kept it stock, no extras like lights, sequencing doors, payload,etc. Only used a lite pilot; tried to keep her on a diet. Very happy with it, youīll like it once dialed in.
Forum: RC Warbirds and Warplanes
05-17-2017, 09:39 PM
Replies: 2,806
Views: 635,828
Posted By AKA2

Well, I went with the Saito fg 60r3, light as the...

Well, I went with the Saito fg 60r3, light as the evo, compared to the fg84r3, and also needed more than 3 pounds. Set the cg 155mm gear down trying to avoid more weight and the first landings...
Forum: RC Warbirds and Warplanes
04-04-2017, 05:37 PM
Replies: 1,126
Views: 371,894
Posted By AKA2

Well, maidened mine with the Saito fg90r3, 1.5...

Well, maidened mine with the Saito fg90r3, 1.5 lbs of lead (more than .5 in front of the cowl, not very proud to put it there, but didnīt want to put it near the engine box and block the air flow,...
Forum: RC Warbirds and Warplanes
03-14-2017, 06:11 PM
Replies: 1,126
Views: 371,894
Posted By AKA2

Good question, couldnīt maiden mine,(saito 90r3)...

Good question, couldnīt maiden mine,(saito 90r3) after warm up and some time, performance droped and was kind of erratic (maybe misfiring), temps were not that high (145-160), cowl is baffled. The...
Forum: RC Warbirds and Warplanes
02-23-2017, 07:53 PM
Replies: 1,126
Views: 371,894
Posted By AKA2

I started my build last nite and as Hot Rod Todd...

I started my build last nite and as Hot Rod Todd suggested I went with the hitec hs 5087 mg servo for the tail gear. Itīs a bit small for the hole but I added a bit of plywood to compensate the...
Forum: Gas Engines
02-14-2017, 03:54 PM
Replies: 640
Views: 252,502
Posted By AKA2

Thanks Mike, talked to your namesake, owner of...

Thanks Mike, talked to your namesake, owner of Gator rc, and says previous kits came with the 9.5" cowls. Newer ones, with 10.5 so bought one with confidence and waiting for it to install this...
Forum: RC Warbirds and Warplanes
02-14-2017, 09:20 AM
Replies: 1,126
Views: 371,894
Posted By AKA2

Same here, gave Mike a call, nice guy btw, and...

Same here, gave Mike a call, nice guy btw, and told me that all zeros he has, come with the bigger cowl so the saito radials 84-90 fit w out mods. I bought the fg90 and now Iīm patiently (donīt think...
Forum: Gas Engines
02-06-2017, 08:28 PM
Replies: 640
Views: 252,502
Posted By AKA2

Hi MikeJM, Iīm too interested in this combo...

Hi MikeJM, Iīm too interested in this combo (Saito-Zero).Did you manage to install it wthout any mods? Inside the cowl measures 9.5" and the outside Saitoīs diameter, the same???
Forum: RC Warbirds and Warplanes
02-02-2017, 07:18 PM
Replies: 1,126
Views: 371,894
Posted By AKA2

Iīm interested in this Zero and want to power it...

Iīm interested in this Zero and want to power it with the new Saito 90r3, which is the same size as the 84. Reading through the thread, itīll need the bigger cowl. So the questiion is, the cowl in...
Forum: RC Warbirds and Warplanes
10-20-2016, 09:13 PM
Replies: 2,806
Views: 635,828
Posted By AKA2

Kevarc, let me tell you that I have this engine...

Kevarc, let me tell you that I have this engine (fg 60r3) with an APC 22x10, Iīve flown her at sea level as well as 4000 ft with success. It flies scale, obviously not overpowered, but I like it. Had...
Showing results 1 to 10 of 10


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.