RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Carl1211
Showing results 1 to 10 of 10
Search took 0.02 seconds.
Forum: Tachometer Readings
01-12-2020, 10:10 AM
Replies: 0
Views: 3,590
Posted By Carl1211

Flywheel magnets for futaba rpm sensor

Has anyone used the flywheel magnets to trigger the rpm sensor from Futaba? (SRS-10RO) I can't find any reference to using the flywheel magnets for magnetic rpm sensors.
Carl
Forum: Gas Engines
10-09-2019, 09:58 PM
Replies: 11
Views: 2,279
Posted By Carl1211

Tell me about oil

Looking for recommendations on 2-cycle oil for fuel mix on Quadra and Zenoah engines. One new and one older motors. 20:1 mixtures but what brand of oil? All synthetic or a blend?

carl
Forum: Glow Engines
10-06-2019, 06:25 PM
Replies: 7
Views: 1,492
Posted By Carl1211

Great gasket selection.

Hobbsy... thank you. I now have gaskets coming to help rebuild 4 engines. Saves me time and replacing repairable engines. Great gasket supplier.
Forum: Glow Engines
10-03-2019, 06:56 PM
Replies: 7
Views: 1,492
Posted By Carl1211

Gasket materials

Cleaning up 2 Magnum pro 45s after 28 years in a box. I need to replace the back plate and front gaskets on reassembly. No parts are available. Do I need to cut new ones from gasket material or will...
Forum: Glow Engines
09-14-2019, 09:05 PM
Replies: 1
Views: 1,141
Posted By Carl1211

Original OS 60 needle settings

I have an os 60 max that sat for 20 plus years. It fires up and runs great on a test stand. But when holding it vertically at full throttle it leans out and dies. I've richness up both high speed...
Forum: The Clubhouse
09-10-2019, 08:57 PM
Replies: 3
Views: 1,533
Posted By Carl1211

Smoke?

Thanks. Do you run smoke on your's? I need to drill the crankcase for a pressure fitting and I am looking for a recommendation for the best location.
Forum: Gas Engines
09-10-2019, 08:54 PM
Replies: 2
Views: 960
Posted By Carl1211

Primer bulb

Have you ever tried putting a small in-line primer bulb on? Once I squirting fuel into the carb to prime it it fires right up. Main problem is when it's coold. Even pulling the prop the
​​​​​prop...
Forum: Gas Engines
09-02-2019, 07:30 PM
Replies: 2
Views: 960
Posted By Carl1211

Quadra 42 pressure fitting

I need to add a crankcase pressure fitting to a quadra 42 for a smoke system and looking for recommendations on position before I crack the case open. Any ideas? Also, best way to prime this thing...
Forum: Giant Scale Aircraft - General
08-14-2019, 06:29 PM
Replies: 3
Views: 1,647
Posted By Carl1211

Giant scale servos

I need an elevator servo for a 40cc biplane. Will a hi-torque futaba be enough or do I need to get a 1/5 futaba servo?
Forum: The Clubhouse
08-04-2019, 08:57 PM
Replies: 3
Views: 1,533
Posted By Carl1211

Quadra 42 kill switch

Trying to figure out how to wire a kill switch on a Quadra 42cdi. It has 2 bare electrical connectors coming out of the ignition. Also, will a DLE OPTO kill switch work on a quadra? Ought it 25...
Showing results 1 to 10 of 10


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.