RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 8
1
2
3
Last »
Search: Posts Made By: radioman789
Showing results 1 to 25 of 190
Search took 0.66 seconds.
Forum: RC Giant Scale Cars
01-06-2007, 05:37 PM
Replies: 105
Views: 15,297
Posted By radioman789

RE: hpi baja or fg marder

hi all and cheers but heres my prob i got the savage for bashing but im bored with bashing and theres no race track except a bmx track and that aint for rc (way too rough )
Forum: RC Giant Scale Cars
01-01-2007, 06:35 PM
Replies: 105
Views: 15,297
Posted By radioman789

hpi baja or fg marder

hi all im almost bored with the nitro savage and want your opinion what should my next investment (lol ) be a hpi baja or fg marder all info is appreciated thanks
Forum: HPI Monster Truck Forum
11-17-2006, 03:34 PM
Replies: 2
Views: 546
Posted By radioman789

LST shocks

hi all im thinking about getting the LST shocks for my savavge i do mainly bashing so would you recomend them and what is the add/disadvantage of them just curious but all advice is appreciated ?
Forum: HPI Monster Truck Forum
09-21-2006, 03:33 PM
Replies: 14
Views: 955
Posted By radioman789

RE: rear wheel savage

thanks all for the replies and just to explain a little bit further i am using ally diff cups with spiders all round and shimmed internally with 5k diff oil and new gasket. brand new ring and pinion...
Forum: HPI Monster Truck Forum
09-20-2006, 01:32 PM
Replies: 14
Views: 955
Posted By radioman789

rear wheel savage

hi all after trashing another ring and pinion gear on the front of my savage i am thinking of just keeping it as a 2 wheel drive by taking the fron diffout what do you guys think and why thanks ...
Forum: HPI Monster Truck Forum
09-16-2006, 03:58 PM
Replies: 23
Views: 2,968
Posted By radioman789

RE: Savage Diff Gears

hi 46U yes i see what your getting at but is doing that ( catching the flat spot with a set screw going to be stronger than a set screw right the hole and threaded as standard ????
Forum: HPI Monster Truck Forum
09-15-2006, 03:55 PM
Replies: 23
Views: 2,968
Posted By radioman789

RE: Savage Diff Gears

hi dude i see you are recomending a hot bodies spiral bevel gear 10 tooth along with the 43 tooth pinoin gear can you tel me how this is fixed to the diff housing as the original 13 tooth bevel...
Forum: HPI Monster Truck Forum
08-28-2006, 04:12 PM
Replies: 12
Views: 653
Posted By radioman789

RE: diff locker any good

excellant post thanks
Forum: HPI Monster Truck Forum
08-28-2006, 01:22 PM
Replies: 12
Views: 653
Posted By radioman789

diff locker any good

hi all i have a almost bog standard savvy 21 ( alloy diff cups with spider mod ) i have stripped the internals of the front diff this time ( last time was rear diff on savvy sts28 )question is...
Forum: HPI Monster Truck Forum
08-20-2006, 08:02 PM
Replies: 7
Views: 414
Posted By radioman789

RE: servo help

heres the source of my query i just bought this servo ebay number 6066132622 and thought the spec was good is it compatible with reciever and rest of radio gear if not then only £12 wasted let me...
Forum: HPI Monster Truck Forum
08-20-2006, 05:00 PM
Replies: 7
Views: 414
Posted By radioman789

RE: servo help

i am using just the standard HPI TF4 transmitter and the crystals are standard 27mhz AM type (green ) doeas it make a difference ???
Forum: HPI Monster Truck Forum
08-20-2006, 10:26 AM
Replies: 7
Views: 414
Posted By radioman789

servo help

hi all iwas wondering if i can use a coreless servo with my standard savage radio gear and if not why? all info is appreciated thanks
Forum: HPI Monster Truck Forum
08-16-2006, 02:05 PM
Replies: 6
Views: 732
Posted By radioman789

RE: diff problem

hi all thanks for the info but still no fix i took out all shims and rebuilt diff see pic as you all see no external parts but still get a grinding noise now and again both diff ends 86064 where...
Forum: HPI Monster Truck Forum
08-15-2006, 04:40 PM
Replies: 6
Views: 732
Posted By radioman789

diff problem

hi all i got a savage 28(sts28) ally diffs (shimmed )all round but i have stripped the standard internal gears of the rear diff all four spider gears are stripped after strip down and clean i tried...
Forum: HPI Monster Truck Forum
08-07-2006, 04:01 PM
Replies: 15
Views: 617
Posted By radioman789

RE: install question

hi mate just take the engine out by removing the four allen key bolts and thi lets you into the spur gear for replacement just remember and check mesh on spur and clutch bell after replacing...
Forum: HPI Monster Truck Forum
06-14-2006, 02:50 PM
Replies: 0
Views: 296
Posted By radioman789

fuel tank mod

hi all i was thinking of doing the fuel tank mod where the tank goes in between the chassis plates any pics and advice would be good ( i got extended LCG plates if it makes a difference thanks
Forum: HPI Monster Truck Forum
05-29-2006, 03:53 PM
Replies: 8
Views: 667
Posted By radioman789

RE: robinson racing clutch and spur .........

hi all i got drag on the ally clutch shoes how do i rectify this small prob ?the CB does not spin free when the engine is out so no drag from SG cheers for all info radman.....
Forum: HPI Monster Truck Forum
05-21-2006, 04:14 PM
Replies: 8
Views: 667
Posted By radioman789

RE: robinson racing clutch and spur .........

hi someguywith......
allright mate i got 3 savages (stock 21 + 1 25 +1 graded with the sts and diff shim and all along with spares to make at least 1 more savvy and my mates a mechanic ) will...
Forum: HPI Monster Truck Forum
05-21-2006, 03:16 PM
Replies: 8
Views: 667
Posted By radioman789

robinson racing clutch and spur .........

hi all i have this set up .. robinson racing clutch and spur 16 /48 and the sts 28 problem i encountered was i stripped the RR spur gear clutch bell was the heavy duty so no damage but after...
Forum: HPI Monster Truck Forum
05-04-2006, 02:34 PM
Replies: 4
Views: 420
Posted By radioman789

RE: strippng wheel hex

cheers guys but addict...... i got jumbo kongs would it do the same to these as my standard wheels and have you got a link for the 23 mm hex and hub also please????
Forum: HPI Monster Truck Forum
05-02-2006, 02:53 PM
Replies: 8
Views: 2,088
Posted By radioman789

RE: Savage 25 will start but then dies

hi mate best idea i got is to set all needles to factory setting watch the video and go from there i know this is basic info but i dont know your experience if nitro and this is a good start hope...
Forum: HPI Monster Truck Forum
05-02-2006, 02:48 PM
Replies: 4
Views: 420
Posted By radioman789

strippng wheel hex

hi all i got the sts 28 engine in the savage with this..... spider diff mod with shims allly clutch shoes titanium spur and hardened clutch bell (16/48)how can i stop the wheel hex from stripping...
Forum: HPI Monster Truck Forum
04-19-2006, 02:28 PM
Replies: 5
Views: 537
Posted By radioman789

RE: Look what i got

hi amec i was admiring your engine ( nice power house ) but can you tell me where you got the wide cable ties for the exhaust muffler as they look sturdy i use satndard ones and the rip the rubber...
Forum: HPI Monster Truck Forum
02-10-2006, 06:44 PM
Replies: 1
Views: 272
Posted By radioman789

stock 21 spur query

hi all my mate has a stock savvy 21 and got a prob........ he stripped his spur due to a bad landing so i gave him my delrin 50 tooth and thought that will keep him on the go BUT after 1 tank tops...
Showing results 1 to 25 of 190
 
Page 1 of 8
1
2
3
Last »


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.