RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: rfbenn
Showing results 1 to 25 of 125
Search took 0.61 seconds.
Forum: RC Jets
02-01-2024, 08:55 AM
Replies: 27
Views: 1,563
Posted By rfbenn

In your transmitter use the AFR for the channel...

In your transmitter use the AFR for the channel you wish to use go to screen 2 at the bottom of the screen there is a speed in and out you can change the numbers , higher numbers mean slower movement...
Forum: RC Jets
02-01-2024, 01:08 AM
Replies: 27
Views: 1,563
Posted By rfbenn

Most modern transmitters can put a delay on a...

Most modern transmitters can put a delay on a servo moving so typically for gear down no delay on the doors but maybe a short delay on the gear and on gear up a delay sufficient to allow the gear to...
01-10-2024, 01:43 AM
Replies: 1
Views: 214
Posted By rfbenn

Go to AFR for your flaps on page 2 you will see...

Go to AFR for your flaps on page 2 you will see at the bottom of the screen speed in and out change the numbers to suit.
0 is normal 27 is very slow page 213 of the manual
Replies: 11
Views: 534
Posted By rfbenn

Try this kindle book by Malcolm Holt, I know it’s...

Try this kindle book by Malcolm Holt, I know it’s for 16 & 18sz but the programming is almost identical to the 12fg and explains things in a much clearer way.

...
10-02-2023, 11:59 PM
Replies: 15
Views: 1,609
Posted By rfbenn

I’m a bit concerned that you are trying to...

I’m a bit concerned that you are trying to replace a capacitor with a battery, you may well completely fry your board.
I had a quick search and found this which looks like the part you’re trying to...
Forum: RC Jets
12-04-2022, 01:24 AM
Replies: 149
Views: 25,539
Posted By rfbenn

Peter 098 I applaud you for bringing a new...

Peter 098 I applaud you for bringing a new product to the market, a brave move which most of us are not prepared to take on.
You may as well totally ignore Highhorse as nothing you say is ever going...
Forum: RC Jets
05-31-2021, 10:38 PM
Replies: 23
Views: 2,848
Posted By rfbenn

Great pictures as always Alastair 👍

Great pictures as always Alastair 👍
Forum: RC Jets
03-01-2021, 09:33 AM
Replies: 1,017
Views: 264,462
Posted By rfbenn

I don’t have another to check it against,...

I don’t have another to check it against, although I had one a while ago and that worked fine so I’m familiar with its operation, I guess this one’s faulty as I got the same result with two different...
Forum: RC Jets
03-01-2021, 02:54 AM
Replies: 1,017
Views: 264,462
Posted By rfbenn

I tried with a Futaba 7008 with the same result...

I tried with a Futaba 7008 with the same result using sbus/serial mode all surfaces were out 5 degrees or so using the loom everything was fine.
Is it worth sending to Bavarian or just use it in...
Forum: RC Jets
02-28-2021, 01:40 PM
Replies: 1,017
Views: 264,462
Posted By rfbenn

Ok so I went through the process again, I...

Ok so I went through the process again, I disconnected the gyro and put the leads back into receiver and confirmed that the surfaces were where I expected them to be .
The receiver is a Futaba 7014...
Forum: RC Jets
02-27-2021, 02:45 PM
Replies: 1,017
Views: 264,462
Posted By rfbenn

I’ll check it out & try again. Thanks

I’ll check it out & try again.
Thanks
Forum: RC Jets
02-27-2021, 08:10 AM
Replies: 1,017
Views: 264,462
Posted By rfbenn

The problem showed up on the initial set up in...

The problem showed up on the initial set up in the workshop using Sbus, as soon as I set it up with the loom ( which doesn’t use sbus) all the surface trims were fine.
I have tried to contact...
Forum: RC Jets
02-22-2021, 07:33 AM
Replies: 1,017
Views: 264,462
Posted By rfbenn

Cortex Pro problem

Hi
I recently bought a Cortex Pro from someone I know, one of the limited edition red versions and put it in my T One Fortune which has been flown many times and is all trimmed out , using the...
02-20-2021, 07:00 AM
Replies: 10
Views: 1,833
Posted By rfbenn

Yes they will, you will need to select the...

Yes they will, you will need to select the correct system mode on the transmitter as it can bind to any current modes .
Forum: RC Jets
08-26-2020, 11:21 PM
Replies: 978
Views: 196,043
Posted By rfbenn

Viper if you can get the cross pins out I have...

Viper if you can get the cross pins out I have successfully removed these rod ends by heating them up with a heat gun, it softens the epoxy up ,the first end will usually pop off as the air inside...
Forum: RC Jets
07-02-2020, 01:01 PM
Replies: 25
Views: 6,973
Posted By rfbenn

I used i3dm’s throws from his T one build thread...

I used i3dm’s throws from his T one build thread here on RCU and have found them fine for me , the factory settings would work too I’m sure. As you say no differential on the factory setting but...
Forum: RC Jets
07-02-2020, 09:16 AM
Replies: 25
Views: 6,973
Posted By rfbenn

These are mine T-One throws Flaps 40mm &...

These are mine T-One throws

Flaps 40mm & 97mm

Ailerons 30mm up 20mm down

Elevators 33 up 28 down

Rudder 60 mm
Forum: RC Jets
06-14-2020, 01:09 PM
Replies: 2,880
Views: 617,333
Posted By rfbenn

I have my c of g set at 260mm which is right on...

I have my c of g set at 260mm which is right on the centre of the wing tube, it flies really well with just a small amount of push on the stick when inverted.
All 4 of my batteries are in the nose...
Forum: RC Jets
05-13-2020, 06:33 AM
Replies: 48
Views: 6,065
Posted By rfbenn

Also consider JetsMunt very easy to get turbines...

Also consider JetsMunt very easy to get turbines serviced even though they are in Spain as are Xicoy.
Not sure where Kingtech servicing is carried out in Europe but not so common over here in the UK
Forum: RC Jets
10-25-2019, 01:25 PM
Replies: 2,880
Views: 617,333
Posted By rfbenn

I started at 250mm but moved back to the centre...

I started at 250mm but moved back to the centre of the wing tube at 260mm, I found at this point it felt comfortable inverted with just a little push on the elevator stick.
As others have said c of...
Forum: RC Jets
09-19-2019, 03:19 AM
Replies: 2,880
Views: 617,333
Posted By rfbenn

I’m sure that the structural integrity of the T-1...

I’m sure that the structural integrity of the T-1 is fine as long as the bolts are checked, a few have been found to be loose from the replies I received at the time , I made the bracket to...
Forum: RC Jets
09-09-2019, 11:34 PM
Replies: 11
Views: 2,384
Posted By rfbenn

Here’s the website address. ...

Here’s the website address.

https://www.limitededitionmodels.co.uk/

Rob
Forum: RC Jets
06-09-2019, 08:36 AM
Replies: 25
Views: 6,973
Posted By rfbenn

This one will help too ...

This one will help too
http://www.rcuniverse.com/forum/rc-jets-120/11628499-new-sport-jet-t-one-models-fortune.html?highlight=T-one+fortune
Forum: RC Jets
06-09-2019, 07:06 AM
Replies: 25
Views: 6,973
Posted By rfbenn

Balance it on the wing tube 260mm it will fly...

Balance it on the wing tube 260mm it will fly fine.
Rob
Forum: RC Jets
04-15-2019, 09:08 AM
Replies: 2,880
Views: 617,333
Posted By rfbenn

3 inch tyres on mine

3 inch tyres on mine
Showing results 1 to 25 of 125
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.