RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: woodland
Showing results 1 to 12 of 12
Search took 0.60 seconds.
Forum: RC Jets
08-14-2012, 04:22 AM
Replies: 188
Views: 39,908
Posted By woodland

RE: What are the ABC's for Gyros in Jets.

Hi from Germany,

I fly a 1/6 F16 Jet Legend with an ACT fuzzy pro on ailerons.
Reason was to compensate the yaw and roll during high alpha approaches with speeds close to stall.

Without...
Forum: RC Jets
05-03-2011, 12:27 PM
Replies: 2
Views: 760
Posted By woodland

RE: F 16 1/6 Flyeagle gear part needed

Of course I did.

The parts are 40 $ a piece, 50 $ Shipping. FEJ points out that there might be an issue, so the parts would have to be a ssembled /aligned by them to ensure correct operation....
Forum: RC Jets
05-03-2011, 10:11 AM
Replies: 2
Views: 760
Posted By woodland

F 16 1/6 Flyeagle gear part needed

I own a Flyeagle F16 1/6 retract set.

To complete the set, I am looking for the components that bear the wheel axles
They swivel along there own axis running through the lower end of the...
Forum: Airtronics Support Forum
01-22-2011, 10:24 AM
Replies: 4
Views: 1,372
Posted By woodland

RE: SD 10 Mixing problem!

thanks for all the help! Works perfectly, me bad vor not seeing the easyiest solution... Happy again, Regards
Forum: Airtronics Support Forum
01-17-2011, 07:16 AM
Replies: 4
Views: 1,372
Posted By woodland

SD 10 Mixing problem!

Hi


Here is an issue with my new SD10:

I fly a small Delta EPP model, called Twinjet made by Multiplex. As a delta plane, it works with combined aileron/elevator control surfaces.

...
Forum: Futaba Radios Direct support forum
01-10-2011, 07:17 AM
Replies: 1
Views: 286
Posted By woodland

RE: R149 DP Rx/Tx compatibility

Hi Gorchew,

if I read your question correctly, there is an easy answer.

All Futaba radios that support to PCM 1024 modulation are able to operate with the 149DP.

Typical radios are:...
Forum: Airtronics Support Forum
01-04-2011, 06:26 AM
Replies: 3
Views: 2,228
Posted By woodland

Free Sync SD-10G software ?

In the link
http://www.airtronics.net/index.php/airtronics-usb-adapter-sd-10g-w-disc.html

it is mentioned, that there is a free sync sw available on airtronics.net.

"Airtronics USB...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
08-14-2010, 07:30 AM
Replies: 0
Views: 378
Posted By woodland

MOVED: Aitronics Sanwa SD-10G combined/ separate trim save

Airtronics Support Forum: http://www.rcuniverse.com/forum/fb.asp?m=9923165
Forum: Airtronics Support Forum
08-13-2010, 01:54 AM
Replies: 6
Views: 1,654
Posted By woodland

RE: Aitronics Sanwa SD-10G combined/ separate trim save

Hi Thud Driver,

thank you very much for your specific helpful contribution.

Regards
Forum: Airtronics Support Forum
08-13-2010, 01:52 AM
Replies: 6
Views: 1,654
Posted By woodland

RE: Aitronics Sanwa SD-10G combined/ separate trim save

Hi Pippin,

any elaborations on your behalf besides
your judgement "outdated"?

Any delibertions concerning your contempary topical approach
contriving the issue?

Thx for...
Forum: Airtronics Support Forum
08-10-2010, 04:12 AM
Replies: 6
Views: 1,654
Posted By woodland

Aitronics Sanwa SD-10G combined/ separate trim save

The SD 10 transmitter offers to save all the trim functions either

separate
or
combined

for all flight conditions, but not separately in each flight condition.

This makes sense...
Forum: JetCat Turbine Direct Support
03-12-2008, 05:30 PM
Replies: 0
Views: 711
Posted By woodland

Dual power supply for Turbine

Hi y’all,

a weak turbine NiCD (though well serviced!) caused a dead stick landing with my jet .

Lots of luck prevented a total loss.

Since then, I am pondering the idea of a dual...
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.