RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: beanutputter
Showing results 1 to 14 of 14
Search took 0.56 seconds.
Forum: Gas Engines
06-24-2005, 03:49 PM
Replies: 11
Views: 1,375
Posted By beanutputter

RE: need tuning help!!!

thats what I thought, but this is a single ring. Think i might tyr a 18-4 or a 16-6
Forum: Gas Engines
06-24-2005, 02:45 PM
Replies: 11
Views: 1,375
Posted By beanutputter

RE: need tuning help!!!

Had a 14-8 sitting around and tried it. It ran pretty good with in, I think this was the problem. The 14-8 is smaller than I hoped to run, what is a good size. Sound like you found the problem...
Forum: Gas Engines
06-24-2005, 01:17 PM
Replies: 11
Views: 1,375
Posted By beanutputter

RE: need tuning help!!!

When I took the carb apart, I did see the regulator and it seemed to be fine. Maybe I am misdiagnosing the symptom; I will have to look at it closer. As far as the prop, I am using an 18-8. I...
Forum: Gas Engines
06-23-2005, 11:25 PM
Replies: 11
Views: 1,375
Posted By beanutputter

RE: need tuning help!!!

Yes, when the fuel tank is above the carb the fuel seem to build up and flood the carb. Engine is hard to start then too.
Forum: Gas Engines
06-23-2005, 10:09 PM
Replies: 11
Views: 1,375
Posted By beanutputter

RE: need tuning help!!!

Thanks for your quick response and good ideas. The fuel does flow unrestricted when disconnected and even pours threw the carb depending on where the tank is mounted. I did check the filter screen...
Forum: Gas Engines
06-23-2005, 09:31 PM
Replies: 11
Views: 1,375
Posted By beanutputter

need tuning help!!!

I have a Ryobi 31cc single ring that I cannot get to tune out. It will idle all day and run at around half with little problem. When I advance above half throttle it dies. I thought it was leaning...
Forum: Kit Building
02-23-2005, 05:59 PM
Replies: 11
Views: 1,052
Posted By beanutputter

RE: My first kit!

about 6oz lead in tail, the evo was heavy, total weight i do not know.
Forum: Kit Building
02-22-2005, 06:13 PM
Replies: 11
Views: 1,052
Posted By beanutputter

RE: My first kit!

Thanks everyone, It took me around two months start to finish, but I had several long periods of down time. I went pretty quick overall.
Forum: Kit Building
02-21-2005, 08:25 PM
Replies: 11
Views: 1,052
Posted By beanutputter

RE: My first kit!

here is another pic
Forum: Kit Building
02-21-2005, 08:22 PM
Replies: 11
Views: 1,052
Posted By beanutputter

My first kit!

This Is my first kit build! It is an uproar 60 with an Evolution 1.00!
Forum: Kit Building
02-21-2005, 08:03 PM
Replies: 4
Views: 767
Posted By beanutputter

RE: 40 size stick kits? all arfs

My gp stick 40 AFF came scalloped if flies great and looks great. I think that is one thing that makes a stick a stick!
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
01-26-2005, 08:27 PM
Replies: 5
Views: 947
Posted By beanutputter

RE: jr transmitter problem

went ahead and opened it up, you were right the fuse was blown. looked good but failed the continuity test.
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
01-26-2005, 08:12 PM
Replies: 5
Views: 947
Posted By beanutputter

RE: jr transmitter problem

i was thinking maybe a fuse but, i also could not see how. do you think my jr warranty will be affected if i open it up
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
01-26-2005, 06:34 PM
Replies: 5
Views: 947
Posted By beanutputter

jr transmitter problem

I have a JR XF631 that is about 3 months old. It is in its first airplane and has been doing fine on its first few trips to the field. I was getting my things ready to go to the field the other day...
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.