RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: zhadley
Showing results 1 to 14 of 14
Search took 0.55 seconds.
Forum: ARF or RTF
08-13-2013, 08:18 AM
Replies: 2,036
Views: 442,296
Posted By zhadley

Thanks, Now I just have to figure out how to get...

Thanks, Now I just have to figure out how to get some support for the rear mounts without making a mess of things! These floats look huge on this plane but I see that others have made it work. I...
Forum: ARF or RTF
08-12-2013, 11:38 AM
Replies: 2,036
Views: 442,296
Posted By zhadley

I was hoping someone that is using the h9 floats...

I was hoping someone that is using the h9 floats could give me a measurement of the distance between the center of the mounts on the plane front to back and side to side. I am attempting to mount...
Forum: ARF or RTF
06-28-2013, 08:44 PM
Replies: 31
Views: 7,342
Posted By zhadley

RE: Aero-Works 30 CC Ultimate

Can someone please measure the cowl width? I'm wondering if the VVRC 40cc twin might be a good fit at 7-7/8".

Thanks!

Zach
Forum: Giant Scale Aircraft - General
02-28-2013, 02:07 PM
Replies: 1,582
Views: 308,806
Posted By zhadley

RE: It's here and Looks GOOD new Hangar 9 Taylorcraft

Does anyone happen to know the size of screws the Cowl uses? I accidentally left them in with the cowl off when breaking in the engine and they vibrated off and blew away! About to maiden mine. I...
Forum: Glow Engines
08-31-2012, 11:19 AM
Replies: 11
Views: 1,316
Posted By zhadley

RE: Tower .61 carburetor question

I don't have a picture but the necessary parts were all part of the remote needle valve and transferred over fine. I will either order a new clip from magnum or OS or just see if the fuel tubing...
Forum: Glow Engines
08-30-2012, 10:05 AM
Replies: 11
Views: 1,316
Posted By zhadley

RE: Tower .61 carburetor question

Thanks for the replies, I'm going to try a couple of the suggestions to increase the needle friction if I can just delete the remote hookup and screw it into the carb body. If not I will pick up the...
Forum: Glow Engines
08-29-2012, 02:27 PM
Replies: 11
Views: 1,316
Posted By zhadley

RE: Tower .61 carburetor question

I would be happy to do without the remote assembly. I still have the issue of no clip to keep the needle from spinning. Are there any good home remedies for this? Thanks for the responses!

...
Forum: Glow Engines
08-29-2012, 06:16 AM
Replies: 11
Views: 1,316
Posted By zhadley

Tower .61 carburetor question

I have a TH 61 that has not been run for a few years that I am trying to get back in service. The bracket holding the remote needle valve is broken. Also the clip/ratchet (not sure the name) that...
Forum: Glow Engines
08-07-2012, 09:39 AM
Replies: 2
Views: 611
Posted By zhadley

RE: ASP/Magnum 1.8 inverted muffler Q

Thanks, just ordered one. I'll report how it works out.

Zach
Forum: Glow Engines
08-06-2012, 09:40 PM
Replies: 2
Views: 611
Posted By zhadley

ASP/Magnum 1.8 inverted muffler Q

I have an ASP 1.80 FS that I am mounting inverted in a cowl (H9 Taylorcraft). I am struggling to find muffler options. Is there anything designed or that will fit this setup? Any suggestions on...
Forum: Glow Engines
05-09-2005, 06:02 PM
Replies: 1
Views: 775
Posted By zhadley

help with magnum pro 45

This was my best running engine however after a crash with no apparent damage, the engine will not idle. No changes in the low speed screw. I tune the high speed and get it just right, but if I...
Forum: 3D Flying!
04-29-2005, 09:57 AM
Replies: 1
Views: 674
Posted By zhadley

RE: Fly RCs banchee g-3d revew q's

Too late! I ordered it. So I guess I'll let anyone know that's interested if it is an adequate setup
Forum: 3D Flying!
04-27-2005, 04:48 PM
Replies: 1
Views: 674
Posted By zhadley

Fly RCs banchee g-3d revew q's

Curious as to peoples opinion of powering this plane with LA .46 and using micro servos for the surfaces. I ask because I have a what I believe strong magnum pro .45 and a few hs-85's and considering...
Forum: ARF or RTF
04-26-2005, 10:07 AM
Replies: 0
Views: 723
Posted By zhadley

comments on Fly RC Banchee G3d review

Curious as to peoples opinion of powering this plane with LA .46 and using micro servos for the surfaces. I ask because I have a what I believe strong magnum pro .45 and a few hs-85's and...
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.